Die-Pat Commercial Sinks and Taps

This is a deck-mounted pre-rinse unit that combines a spring-action goose-neck spray arm with a lever-operated rose shower head and a separate bowl-filling tap, both sharing the same deck fixing. It carries WRAS approval, meaning it meets UK Water Regulations Advisory Scheme standards for direct connection to mains water supplies in commercial premises. The unit arrives pre-assembled, which removes a reasonable amount of installation complexity at the sink station.

At a busy ware-wash station, a pre-rinse unit is one of the hardest-worked fittings in the kitchen. It handles food debris rinsing from crockery, pots, and trays ahead of the dishwasher, fills sinks during ongoing wash cycles, and supports general station clean-down throughout a full service. Quarter-turn ceramic cartridge taps respond quickly under repeated daily use and are straightforward to service when a cartridge eventually needs attention. The spring-action goose-neck keeps the hose under control between uses, which matters in a tight sink area where a trailing hose creates a practical hazard.

• WRAS approval for compliant direct mains connection in commercial premises
• Pre-assembled unit reduces fitting time and complexity at the sink station
• Quarter-turn ceramic cartridge taps for fast, reliable flow control
• Spring-action goose-neck with rose head for thorough pre-rinse coverage
• Adjustable wall bracket included to manage hose positioning during use

Because this is a deck-mounted unit, it requires a sink with appropriate fixing holes at the correct centres. If you are retrofitting to an existing sink, confirm deck thickness and hole spacing before ordering. WRAS approval means it can typically be connected directly to the mains without a secondary backflow device where regulations permit, though your installer should confirm local requirements. Water connections should be made by a competent plumber.

This unit suits café, restaurant, pub kitchen, and canteen environments where a reliable, compliant pre-rinse setup is needed without unnecessary complexity. For sites running very high continuous dishwasher throughput, it is worth considering whether a more heavy-duty spray unit would better match the workload.

If you are not sure whether this configuration fits your existing sink or water supply arrangement, we are happy to talk it through before you commit to an order.

This is a single-feed pre rinse spray arm unit designed for commercial sink stations. It combines a quarter-turn lever tap with a ceramic cartridge, a spring-action goose neck, and a hand-held spray gun on a flexible hose — the standard configuration for rinsing crockery, pots, and trays before they enter a dishwasher or glasswasher. WRAS approval confirms the unit meets UK Water Regulations Advisory Scheme requirements, which is a prerequisite for mains-connected installation in any commercial premises.

In a working kitchen, a pre rinse unit takes considerable daily punishment. The ceramic cartridge delivers smooth, consistent quarter-turn operation that holds up reliably under repeated use throughout a busy service. The spring-action goose neck keeps the hose clear of the work surface and returns it to a neutral position between uses — a small detail that matters in a pot wash area where workflow and tidiness both count. The unit arrives pre-assembled, and the adjustable wall bracket offers some flexibility when fitting to existing sink structures or varied wall positions.

• WRAS approved for compliant mains water connection in commercial premises
• Ceramic cartridge tap for reliable, long-lasting quarter-turn operation
• Spring goose neck keeps hose tidy and reduces clutter at the sink
• Pre-assembled to reduce installation time on site
• Adjustable wall bracket accommodates varied sink and wall configurations

This unit is well suited to small and medium kitchens with a single sink station. Sites running high-throughput dishwash operations or multiple sink positions may find a heavier-duty or dual-feed configuration more appropriate. Before ordering, it is worth checking the wall bracket reach and hose length against your sink depth and wall-to-sink distance to confirm the fit is right for your setup.

If you are unsure whether this unit suits your sink arrangement or water supply, we are happy to talk it through.

• 7" dual flow swivel spout
  
• The durable chrome plated finish
• WRAS approved
• The image shown represents the product although the actual product supplied may differ slightly in appearance - features and dimensions should be discussed if critical

This is a wall-mounted, dual-feed pre-rinse spray unit designed for commercial sink stations. It combines a monobloc tap body with a flexible goose-neck rinse arm, giving the operator independent control of hot and cold water alongside a dedicated spray function for rinsing crockery, pots, and food preparation surfaces. WRAS approval confirms the unit meets UK water regulations — a requirement for any fixture connected to the mains in a commercial kitchen.

In a working kitchen, a pre-rinse arm is a practical tool rather than an optional extra. It speeds up the pre-wash stage before dishwashing, reduces food residue build-up in the sink bowl, and keeps the pot wash area moving during busy service. The quarter-turn lever taps with ceramic cartridges operate quickly under repeated daily use and hold up reliably without dripping or stiffening over time.

• WRAS approved for compliant mains connection in commercial premises
• Quarter-turn ceramic cartridge taps for fast, consistent operation
• Spring-action goose-neck hose for controlled reach and easy positioning
• Lever-operated spray gun for variable rinse pressure at the point of use
• Pre-assembled unit with adjustable wall bracket included for straightforward fitting

Installation requires hot and cold water feeds and a wall surface capable of supporting the bracket. The adjustable bracket gives some flexibility on positioning, though placement should be planned around the sink bowl and drainage to avoid splash issues. This unit is suited to standard sink station use — for high-volume dishwash induction points, a heavier-duty pre-rinse column may be more appropriate.

It is a sensible choice for small to mid-sized kitchens, cafés, pub kitchens, and sandwich or prep operations where a reliable, regulation-compliant rinse point is needed without the complexity of a full column system. If you would like to talk through whether this suits your sink setup or water supply configuration, we are glad to help before you place an order.

This deck-mounted monobloc combines a pre-rinse spray arm and a 12" bowl-filling tap in a single fitting. WRAS approval confirms the unit meets UK Water Regulations Advisory Scheme standards — a requirement for any equipment connected to the mains water supply in a commercial food environment. The unit arrives pre-assembled, which reduces installation time and removes the risk of on-site assembly errors.

In a working kitchen, the pre-rinse station is one of the hardest-worked points in the pot wash or dishwash area. The spray arm allows staff to clear plates, pots, trays, and utensils quickly before loading them into a dishwasher or glasswasher, helping to protect spray arms from debris and extending the intervals between full machine cleaning cycles. Having the bowl-filling tap integrated into the same deck fitting means the station handles both rinsing and filling duties without a second penetration in the sink deck.

For day-to-day operation, the main practical advantages are:

• WRAS approval satisfies water byelaw compliance requirements for commercial installations
• Pre-assembled design simplifies installation and reduces plumber preparation time
• Combined fitting reduces the number of deck penetrations required
• Flexible hose and wall bracket included, ready for connection to hot and cold supplies
• Deck-mounted format suits standard commercial sink fabrications

The unit requires a suitable pre-drilled deck hole of the correct diameter in the sink or fabrication it is fitted to. Hot and cold supplies must be accessible beneath the deck for the flexible hose connections. Installation should be carried out by a qualified plumber with experience of commercial water fittings. For single-sink or pot wash stations this is a straightforward solution, but very high-throughput sites running multiple rinse stations continuously may find a heavier-duty or wall-mounted configuration more appropriate for their demands.

This unit is well suited to cafés, pub kitchens, small to medium restaurants, and contract catering sites where a reliable, compliant everyday pre-rinse station is needed without unnecessary complexity. If you are fitting out a new sink station or replacing an existing unit and want to confirm it is the right choice for your setup, the team is happy to talk it through with you beforehand.

3" lever ceramic disc
Lever action pillar sink taps

• Features 1/4 turn ceramic disc for rapid on/off flow.

1/4 turn ensures a rapid ON/OFF operation of your tap. The ceramic disc cartridge ensures a smooth a smooth ON/OFF operation and eases use of tap.

The Advantage HB300PFB-WRAS is a wall-mounted, knee-operated wash hand basin designed for commercial catering and food preparation environments where hands-free operation is a hygiene or regulatory requirement. WRAS approval confirms the unit meets Water Regulations Advisory Scheme standards for connection to the UK mains water supply — a requirement that commonly arises during environmental health inspections and new build sign-offs.

The knee-operated timed tap allows kitchen staff to start and stop the flow of water without hand contact, reducing the risk of cross-contamination at the point of handwashing. This is particularly relevant in food production units, prep kitchens, and any operation running under HACCP-based hygiene protocols. The integral rear splashback protects the wall surface around the basin, and the satin finish wipes down cleanly during routine kitchen cleaning.

• Hands-free operation reduces cross-contamination risk at the handwash point
• WRAS-approved components satisfy water fittings regulations for commercial sites
• Timed tap limits unnecessary water flow, reducing running waste
• Integral splashback protects the wall and simplifies daily cleaning
• Compact wall-mounted profile suits tight spaces and secondary wash points

Installation is straightforward for a competent plumber. The unit is wall-mounted via keyhole slots, so the fixing surface should be assessed beforehand — plasterboard alone is unlikely to provide adequate support, and a solid substrate or appropriate fixing frame will be needed. The basin connects to a standard hot and cold supply through the mixing valve and discharges via a 1½ inch waste outlet. A combined overflow and waste kit is supplied, which simplifies the installation. Proximity to an existing plumbing run will keep costs and complexity down; a long new run adds to both.

This basin is well suited to small and medium commercial kitchens, cafés, school kitchens, and any site where a dedicated handwash station is required by food hygiene legislation. It is a practical, compliance-focused fixture rather than a high-throughput installation — operations with large staff numbers or multiple simultaneous users may find a second unit or a higher-capacity alternative more appropriate.

If you are fitting out a new kitchen or need to confirm this basin meets your site's specific requirements, our team is happy to talk it through with you before you commit to an order.

• Pair of 1/2 inch basin taps
• The durable chrome plated finish
• WRAS approved
• Image is representative of product

• Pair of 1/2 inch basin taps
• The cross-top handwheels
• The durable chrome plated finish
• WRAS approved
• Image is representative of product

This twin pillar pre-rinse spray unit is built for pot wash and preparation sinks in commercial kitchens. Rather than mounting through the sink deck, it fixes to the wall via an adjustable bracket — a practical arrangement where the sink surface is already occupied or where a more secure, stable fixing point is preferred. WRAS approval confirms the unit meets UK water regulations for connection to the mains supply, which is a compliance requirement in virtually all commercial premises.

In a working kitchen, a pre-rinse unit takes constant, rough-and-ready use throughout service. The quarter-turn lever taps with ceramic cartridges handle that well — they operate quickly under wet or gloved hands and hold up better over time than conventional washer-based designs. The spring-action gooseneck keeps the hose returned to a set position between uses, reducing trailing hose hazards in a busy sink area. The lever spray gun allows controlled, one-handed rinsing, which matters when the other hand is managing crockery or cookware.

• WRAS approved for compliant mains connection in commercial premises
• Ceramic cartridge quarter-turn levers for reliable, low-maintenance operation
• Spring-action gooseneck manages hose position during busy service
• Lever spray gun for controlled, one-handed rinsing
• Adjustable wall bracket included for flexible positioning

The unit arrives pre-assembled, which reduces time on site. Connection to the water supply should be carried out by a qualified plumber. The adjustable wall bracket accommodates most standard sink configurations, making this a straightforward fit for cafés, pub kitchens, school canteens, and similar environments. For very high-throughput pot wash areas running extended shifts, it is worth considering whether a heavier-duty rinse setup would be more appropriate for the workload.

If you want to check this suits your existing sink arrangement before ordering, the team is happy to talk it through.

• Pair of 1/2 inch lever taps
• The durable chrome plated finish
• WRAS approved
• The image shown represents the product although the actual product supplied may differ slightly in appearance - features and dimensions should be discussed if critical

The Advantage HB290S is a wall-mounted hand wash basin constructed from 304-grade stainless steel with a polished finish. It is designed specifically for commercial kitchen environments where a dedicated hand wash point is required to meet food hygiene regulations. The circular bowl, upstand, and apron skirt are fully spot-welded as a single unit, which reduces installation time and eliminates the joints where bacteria can accumulate.

In a working kitchen, a hand wash basin needs to be robust enough to withstand constant daily use without flexing, corroding, or deteriorating around fixings. The fully welded construction of the HB290S holds up well under these conditions, and the polished 304 stainless finish is straightforward to wipe down and keep clean to the standards expected by environmental health officers.

• Keyhole mounting system speeds up wall fixing during installation
• Overflow included, reducing the risk of water spillage onto the floor
• Waste fitting included — no additional purchase required before fitting
• Fully welded apron-to-bowl joint for hygiene and structural rigidity
• Polished stainless finish easy to clean and compliant with food hygiene environments

Installation is straightforward. The keyhole fixing system allows the basin to be positioned and secured quickly to a solid wall, though the wall surface and fixings need to be appropriate for the weight and the conditions — a damp kitchen environment calls for non-corrosive fixings throughout. You will need a plumber to connect the waste outlet and, if not already in place, to install a suitable tap above the basin. The 25mm upstand helps contain minor splashing at the wall.

This basin is well suited to small and medium-sized commercial kitchens, food preparation areas, café back-of-house spaces, and any environment where a compact, regulation-compliant hand wash point is needed. For larger sites or higher-traffic washrooms requiring a wider bowl or additional features, it is worth discussing whether a different specification would be more appropriate.

If you are unsure whether this basin suits your layout or compliance requirements, the team is happy to talk it through with you before you order.

The Advantage HB240S is a wall-mounted hand wash basin manufactured in polished 304 grade stainless steel, intended for commercial kitchens, food preparation areas, and other environments where dedicated hand washing provision is a regulatory requirement. The circular bowl and compact overall footprint make it practical in locations where wall space is limited.

In a working kitchen, hand wash basins take a good deal of daily use. The fully spot-welded construction — including the apron — means the unit holds its form under regular heavy-handed use without the flex or joint weakness that can develop on lighter-gauge alternatives over time. The polished finish is straightforward to wipe down and maintain to the standard expected during environmental health inspections.

From an installation standpoint, the keyhole mounting system is a practical detail that saves time on site — the basin can be hung and levelled without the need for additional brackets or complex fixings. A waste fitting is included, reducing the number of components that need to be sourced separately. The 25mm upstand provides a degree of splash protection to the wall surface behind.

• Compact footprint suits tight wall runs and narrow prep areas
• Spot-welded construction including apron for structural integrity
• Keyhole mounting simplifies fixing and reduces installation time
• Polished 304 stainless steel cleans easily to inspection standard
• Waste fitting included, reducing additional procurement

This basin is well suited to smaller commercial kitchens, cafés, food vans, and secondary wash points within larger operations. For sites requiring larger bowl capacity or additional features such as an overflow, it is worth considering whether a larger model from the range would be more appropriate for the volume of use expected.

If you are fitting out a new kitchen or replacing an existing unit and want to confirm the right specification before ordering, our team is happy to talk it through.

• Pair of 1/2 inch basin taps
• The durable chrome plated finish
• WRAS approved
• Image is representative of product

• Pair of 1/2 inch basin taps
• The cross-top handwheels
• The durable chrome plated finish
• WRAS approved
• The image shown represents the product although the actual product supplied may differ slightly in appearance - features and dimensions should be discussed if critical