Grill Accessories

The Lincat GR3/FS is a dedicated floor stand designed solely for use with the Lincat GR3 salamander grill. Rather than wall-mounting the grill or occupying bench space, this stand converts the unit into a freestanding, floor-level installation at a practical working height. It is not a universal fitting and is not compatible with other Lincat salamander models.

In a working kitchen, salamander positioning has a direct effect on service flow. Chefs finishing, glazing, and holding dishes at the pass need reliable, comfortable access without unnecessary reaching or adjusting. A correctly positioned salamander keeps throughput consistent during busy service, and the stand provides that stability in kitchens where wall-mounting is not feasible — whether due to layout constraints, surface material, or the need to occasionally reposition the unit.

The open-frame construction allows cleaning access around and beneath the grill, which helps prevent grease and debris accumulating at floor level. This is a practical advantage in kitchens subject to routine environmental health inspection, where evidence of thorough cleaning access matters.

• Converts the GR3 salamander to a stable freestanding installation
• Raises the grill to a comfortable working height at the pass
• Open-frame base allows cleaning access beneath the unit
• Suited to kitchens where wall-mounting is not practical
• Self-contained — no wall fixing or bench space required

When planning the installation, account for the increased overall height of the combined unit and ensure adequate overhead clearance for safe operation and ventilation. This stand is specific to the GR3 and should not be assumed to fit other models.

If you are planning a new salamander setup and want to confirm the right configuration for your kitchen, we are glad to talk it through.

The Lincat OA8911 is a purpose-built wall shelf designed to be used alongside compatible Lincat salamander grills. As a manufacturer-matched accessory rather than a generic bracket, the fixing geometry and positioning are intended to work with specific Lincat salamander models — which makes for a cleaner, more reliable installation than adapting an off-the-shelf solution.

At the grill section or pass, a properly positioned shelf earns its place quickly. It gives chefs a dedicated surface close to the salamander for plates, dressed dishes, or items queuing to be finished under the heat. During a busy service, that structural tidiness reduces the small inefficiencies that build up when surfaces are improvised or when the immediate area around the grill becomes cluttered.

• Manufacturer-matched design for a secure, intended fit with compatible Lincat salamanders
• Wall-mounted to keep the area beneath and around the grill clear
• Dedicated surface positioned close to the heat source for pass efficiency
• Supports an organised workflow during high-volume covers
• Straightforward installation — no complex setup required

One practical point before ordering: Lincat produce several salamander variants and not all accessories are interchangeable across the range. It is worth confirming your existing unit is compatible with the OA8911 before purchasing — a quick check avoids a mismatch on delivery.

This shelf suits operators who already own a compatible Lincat salamander and want to make better use of the space and workflow around it. If you are unsure whether it will fit your current setup, the team are happy to check compatibility before you place an order.

The Lincat GR7/BS is a purpose-built bench stand designed to support the Lincat GR7 salamander grill at a practical working height on a countertop or pass surface. It is matched specifically to the GR7, so it is worth confirming your salamander model before ordering if there is any uncertainty about which unit is in use.

Grill height has a more direct effect on working efficiency than it might first appear. A salamander positioned directly on a flat surface tends to sit too low for comfortable use during service, which can lead to awkward posture and slower working pace when throughput matters most. The stand brings the GR7 to a more natural sightline, reduces unnecessary reaching, and clears the space beneath the unit for trays, dishes, or brief plate staging during a busy pass.

• Positions the GR7 at a more ergonomic working height on bench or pass
• Creates usable clearance beneath the unit during service
• Matched specifically to the GR7 — no adaptation or modification required
• Well suited to kitchens where bench mounting is preferred over floor-standing
• Supports a tidy, well-organised pass arrangement

This stand is a common choice in kitchens with limited floor space where keeping the salamander on a bench or shelf unit is the more practical layout. It is not a universal accessory and is not suited to other salamander models in the range.

If you are planning a salamander installation and want to confirm the right stand or mounting arrangement for your kitchen layout, we are happy to talk it through.

The Parry 1875 is a set of wall mounting brackets designed specifically for use with the Parry 1872 salamander grill. Rather than occupying counter or shelf space, the brackets allow the salamander to be fixed directly to a wall surface, keeping the unit at a practical working height and freeing up the space beneath for other tasks.

In a busy kitchen, counter space is rarely in surplus. Wall-mounting a salamander is a straightforward way to reclaim that space without compromising access to the grill during service. The brackets are purpose-made for the 1872, so fitment is a direct, matched installation rather than an improvised workaround.

A few practical points worth considering before purchasing:

• Designed specifically for the Parry 1872 salamander — confirm compatibility before ordering if you have a different model
• Wall construction must be capable of supporting the weight of the mounted grill safely
• Installation should be carried out by a competent engineer or tradesperson
• The mounting position will affect usable working height — worth thinking through before fixing

These brackets are a straightforward accessory suited to kitchens where wall-mounting the 1872 salamander makes sense operationally — typically smaller kitchens with limited bench space, or where a fixed installation is preferred for workflow reasons.

If you're unsure whether these brackets are the right fit for your setup, or you'd like to talk through the installation requirements, we're happy to help.

The Lincat GR7/WS is a wall-mounting shelf made specifically for the Lincat GR7 salamander grill. Rather than sourcing a general-purpose bracket or fabricating something on site, this shelf is matched to the GR7's footprint and fixing points, providing a secure and correctly positioned mount above the cooking line without any guesswork.

Wall-mounting a salamander makes a genuine difference to day-to-day kitchen workflow. Positioning the unit at the right height lets operators work beneath it efficiently — finishing plates, browning, or glazing — whilst keeping counter space free for active service use. It also simplifies cleaning along the cooking line and helps maintain a clear, organised pass during busy periods, which matters when the kitchen is running at pace.

• Frees up counter space beneath the grill for active service use
• Positions the GR7 at a practical working height for operators
• Purpose-matched to the GR7, removing the need for improvised brackets
• Simplifies cleaning around the base of the unit and along the range top
• Contributes to a tidier, better-organised pass setup during service

This shelf is designed for the GR7 model specifically and should not be assumed compatible with other Lincat salamander variants. Wall fixings will need to be appropriate for the surface — a solid masonry wall or adequately studded partition with suitable anchors is the standard requirement. If there is any uncertainty about wall construction or load-bearing suitability, it is worth confirming this before installation begins.

The GR7/WS suits any site running a Lincat GR7 salamander where wall-mounting is the preferred arrangement over counter placement — most commonly pub kitchens, café operations, and smaller restaurant sites where worktop space is at a premium.

If you are specifying this shelf alongside a new GR7 installation or have questions about wall fixing requirements, the team are glad to talk it through before you commit.

The Lincat OA8909 is a purpose-made wall shelf designed to mount directly at the grill station alongside compatible Lincat salamander grills. It provides a fixed, stable surface for plates, resting dishes, and service items — keeping what the operator needs close to hand without cluttering the surrounding bench space.

At the grill station, a well-positioned shelf is one of those additions that proves its worth quickly during service. Having a dedicated surface at the unit tightens workflow, reduces unnecessary movement, and helps maintain an organised pass when covers are moving at pace. It is a straightforward piece of kit, but the absence of one becomes noticeable under pressure.

Being a genuine Lincat accessory rather than a generic aftermarket bracket, the OA8909 is engineered to align correctly with the relevant salamander models. This matters for a clean, secure fit and for safe wall installation — aftermarket alternatives can present alignment issues at the manufacturer fixing points.

One consideration worth noting before ordering: Lincat produce several salamander variants and not all accessories are interchangeable across the range. Confirming your exact salamander model reference before purchasing is a sensible step to ensure the OA8909 is the right shelf for your specific unit.

If you would like to check compatibility with your current equipment before going ahead, our team is glad to help.

The Parry 7072FS is a purpose-built floor stand designed exclusively for the Parry 7072 grill. It does one job and does it well: raises the parent unit to a practical working height and gives it a stable, fixed footprint on the kitchen floor. It is not a universal stand and is not compatible with other equipment.

In a working commercial kitchen, having equipment positioned at the correct height makes a genuine difference over a long service. Operators avoid stooping or reaching awkwardly, which matters when a grill is in near-constant use during a busy period. A dedicated stand also lifts the unit clear of floor-level moisture and debris, makes cleaning beneath and around the equipment more straightforward, and contributes to a tidier, more organised kitchen layout.

• Raises the Parry 7072 to a comfortable, ergonomic working height
• Creates a stable, dedicated footprint to prevent movement during use
• Lifts the unit clear of the floor, supporting hygiene and easier cleaning
• Keeps the kitchen layout organised with equipment properly sited

From a practical standpoint, the stand is straightforward to incorporate into a new or existing installation. It is worth confirming floor surface and levelness before fitting, as any unevenness beneath the stand will affect stability. Kitchens with limited floor space should consider the combined footprint of the stand and unit together when planning the layout.

The 7072FS is the right choice for operators running the Parry 7072 who need the unit freestanding at counter height rather than bench-mounted. If you are unsure whether this stand suits your installation or how it fits within your existing setup, we are happy to talk it through.

The Parry 7073FS is a floor stand designed specifically to work with the Parry 7073. Its primary purpose is to raise the unit to a practical working height, allowing the 7073 to operate as a freestanding piece of equipment where bench or countertop mounting is not possible or not preferred.

For kitchens where the 7073 is a primary piece of service equipment and floor positioning suits the layout better than a built-in bench solution, this stand provides a straightforward means of achieving that setup. It is a dedicated accessory rather than a universal stand, so compatibility with the 7073 is assured.

We currently have limited detail available on the construction, load rating, and any height adjustability of this stand. Before ordering, it is worth confirming with us that it suits your floor type, available footprint, and how it fits into your wider kitchen layout — particularly if the grill will be in a high-traffic section of the kitchen.

If you are specifying the Parry 7073 as part of a wider equipment setup and are unsure whether floor-mounting is the right approach for your space, we are happy to talk it through.

The Parry 7075 wall brackets are a purpose-made mounting accessory designed to allow compatible Parry grill and charcoal units to be fixed securely to a wall. Rather than sitting on a stand or countertop, wall-mounted installation can free up valuable worktop space and create a cleaner, more permanent setup in a busy service kitchen.

These brackets are confirmed as compatible with Parry models 1872, CPG, CAS, and CAS2. If you are unsure whether your specific model is covered, it is worth checking before ordering — fitting the wrong bracket to a heavy piece of equipment is a straightforward problem to avoid with a quick conversation.

Wall mounting a grill unit does introduce some practical considerations worth thinking through before installation: the wall structure must be capable of bearing the combined weight of the bracket and the unit, appropriate fixings will need to suit the wall material, and positioning should account for adequate clearance to surrounding surfaces and ventilation requirements above the unit. In most cases this is a job for a competent installer or gas engineer depending on the type of unit being mounted.

These brackets suit kitchens where space efficiency matters and a fixed, permanent grill position is preferable to a freestanding arrangement. They are a simple but practical addition when setting up or reconfiguring a Parry grill installation.

If you would like to confirm compatibility with your existing Parry equipment or discuss your installation setup, the team is happy to help you work through the specifics before you order.

The Lincat GR3/WS is a wall-mounted shelf designed specifically to match the Lincat GR3 salamander grill. Its purpose is straightforward: to provide a secure, correctly rated fixing point that positions the GR3 at a consistent working height on the wall, freeing the counter or pass surface beneath for other use.

In a working kitchen this arrangement makes a practical difference. A wall-mounted salamander sits at a fixed, repeatable height throughout service, remains stable under the incidental contact that bench-mounted units can attract, and allows operators to work comfortably beneath it without obstruction. Cleaning around and below the unit at close-down is also more manageable when the space is fully clear.

Using the manufacturer-matched shelf is worth doing for reasons beyond convenience. The GR3/WS is engineered to align with the GR3's fixing geometry and carry its load correctly. A generic bracket may not suit the unit's weight distribution or mounting points, which introduces unnecessary risk in a busy service environment.

Installation requires the shelf to be fixed securely into a wall capable of bearing the combined weight of the shelf and the grill. Wall construction varies — solid masonry, stud partitions, and tiled surfaces each call for different fixings and approaches — so it is worth assessing the substrate before ordering. Fixing should be carried out by a competent installer or kitchen fit-out contractor rather than attempted without the appropriate fixings for the wall type.

This shelf suits any kitchen running a Lincat GR3 salamander where wall placement is the preferred arrangement. If you are considering the installation approach or want to confirm the GR3 is the right unit for your kitchen, the team is happy to talk it through with you.

The Parry 1876 is a branding plate designed exclusively for use with the Parry 1872 salamander grill. It attaches to the host unit and allows operators to apply consistent char-mark lines to meat, fish, and other grilled items directly under the salamander element — producing the kind of branded, visually finished result that grill-led menus typically require.

In a busy service environment, a branding plate like this gives the salamander a secondary function without the footprint or cost of a dedicated chargrill. That is particularly useful on tighter service lines where space is limited but the menu demands a marked finish. Consistency across covers is straightforward to maintain, which reduces variation on the pass during peak service.

• Adds char-mark capability to an existing salamander station
• Removes the need for a separate chargrill on space-constrained lines
• Supports consistent plate presentation throughout service
• Extends the functional range of the Parry 1872 without additional equipment
• Straightforward to integrate into an established grill station setup

Because this is an accessory rather than a standalone unit, compatibility is the key consideration before ordering. The 1876 is confirmed for use with the Parry 1872 salamander and is not a universal fitting. If you are specifying a new grill station from scratch or are uncertain whether your current salamander is the correct model, it is worth confirming before you purchase.

If you would like to talk through how this accessory fits your existing setup, the team is happy to help you get it right.

The Lincat GR3/BS is a purpose-built bench stand designed exclusively to support the Lincat GR3 salamander grill. Its function is straightforward: it raises the unit from worksurface level to a more practical operating height, giving kitchen staff proper access to finishing and browning tasks without stooping or overreaching during a busy service.

Salamander positioning matters more than it is often given credit for. A unit sitting directly on a worktop can sit at an awkward height that slows chefs down when checking dishes, rotating trays, or retrieving plates under pressure. A well-positioned salamander keeps that workflow moving cleanly, which adds up across a full shift. The GR3/BS addresses this without requiring any structural alteration to the kitchen.

From a hygiene standpoint, the stand is built to meet the expectations of a commercial kitchen environment. It keeps the GR3 stable and secure on the bench while leaving the area beneath open and accessible — an important consideration when daily cleaning routines are part of your compliance obligations.

• Raises the GR3 to a practical, ergonomic working height for kitchen staff
• Provides a stable, secure base to prevent movement during service
• Leaves the area beneath the unit open and easy to clean
• Constructed to commercial kitchen hygiene standards
• Matched specifically to the Lincat GR3 — not a universal fitting

It is worth noting that this stand is matched to the GR3 model only. If you are working with a different Lincat salamander, compatibility should be confirmed before ordering to avoid a mismatch on installation day.

If you are unsure whether this stand suits your bench configuration or kitchen layout, we are happy to talk it through with you.

The Lincat OA8912 is a purpose-built floor stand designed to support compatible Lincat salamander grills at a practical working height. Rather than relying on a fabricated shelf, a borrowed worksurface, or an improvised support, it gives the salamander a dedicated, stable base on the kitchen floor — keeping the unit accessible and the surrounding workspace clear.

In a busy service environment, ergonomics have a direct effect on throughput. A salamander at the wrong height slows down loading and retrieval, particularly during peak periods when speed and consistency are critical. This stand positions the grill where operators can work with it comfortably, rather than having to adapt their workflow around it. The construction meets applicable hygiene standards, with surfaces and joints that are straightforward to clean down — a practical consideration when environmental health compliance is part of routine kitchen management.

• Positions the salamander at a comfortable, practical working height
• Provides a stable, dedicated floor-mounted base without improvised solutions
• Designed to hygiene standards with cleanable surfaces and joints
• Keeps the grill clear of worksurface clutter and congestion
• Straightforward to install alongside a compatible Lincat salamander

This stand is designed for specific compatible Lincat salamander models, so confirming compatibility with your existing or intended grill before ordering is an important step. It requires adequate floor space and a stable, level surface, and the grill should be properly secured to the stand prior to use.

It is well suited to kitchens where a compatible Lincat salamander is already in place or being specified as part of a new installation, and where floor-mounting is the preferred or only practical option. If you are unsure whether this stand suits your grill model or available space, we are happy to talk it through.

The Lincat BR51 is a wall mounting bracket designed to allow compatible Lincat salamander grills to be installed overhead rather than taking up worktop or counter space. It is a straightforward, purpose-made accessory rather than a standalone piece of equipment, but for many kitchens it makes a meaningful difference to how the pass or cooking line is organised.

In busy service environments, worktop space is rarely in surplus. Mounting a salamander overhead using a properly rated bracket keeps the unit accessible for finishing dishes, toasting, and gratiné work, while freeing the surface below for plating or prep. The BR51 is built to suit the Lincat salamander range it was designed for, which means the fit, load rating, and fixing points are matched to the grill rather than adapted from a generic solution.

A few practical points worth considering before ordering: wall mounting a salamander requires a suitable solid masonry or adequately reinforced wall surface — a standard stud partition will not be appropriate without additional structural provision. The bracket positions the grill at a fixed height, so it is worth confirming the working height suits your pass layout before installation. You should also ensure the wall location keeps the unit within reach of its power supply without creating a cable management problem.

The BR51 is the correct accessory for operators running compatible Lincat salamander models who want to reclaim worktop space without relocating the unit entirely. It is not a universal fit and should be confirmed against your specific salamander model before purchase.

If you are unsure whether this bracket suits your existing grill or your kitchen's wall construction, our team are happy to talk it through with you.

The Lincat OA8908 is a purpose-built bench stand designed to support compatible Lincat salamander grills at a practical working height on a countertop or preparation surface. Rather than sitting the grill flush on a flat bench, the stand raises it so chefs can load, monitor, and clear food more naturally during service without stooping or interrupting their workflow at the station.

In a working kitchen, grill height has a measurable effect on how smoothly service runs. A salamander positioned too low on a busy pass creates awkward movement at a point in the operation where efficiency matters most. A consistent, stable working position makes the station easier to manage across a full service, particularly where chefs are covering multiple sections at once.

From an operational standpoint, the stand also contributes to a tidier, safer grill station:

• Raises the salamander to a more accessible working height on the bench
• Provides a stable, fixed base that reduces movement and vibration during use
• Keeps the underside of the grill clear, supporting airflow and surface hygiene
• Matched to specific Lincat salamander models, ensuring a secure and stable fit
• Supports compliance with commercial kitchen surface hygiene requirements

It is worth confirming compatibility with your specific salamander model before ordering. This stand is matched to particular Lincat units, and fitting an incompatible grill introduces both a stability and a safety risk. If you are specifying a new salamander and stand together, or are unsure whether this suits your existing equipment, it is worth checking before purchasing.

If you would like to confirm compatibility or talk through how this fits into your grill station setup, the team is happy to help.

The Lincat OA8918 is a purpose-built bench stand designed to support specific Lincat salamander grills — the OG7302 and OE7304 models. Rather than resting the grill directly on a worktop or improvising a platform, this stand raises the unit to a practical working height while keeping the installation stable and in keeping with commercial hygiene requirements.

In a working kitchen, the height at which a salamander sits has a direct effect on how quickly and safely chefs can load, monitor, and retrieve food during service. A matched stand removes the guesswork from that setup. Because it is designed specifically for these Lincat units, the fit is secure and the overall installation behaves as intended — there is no movement or instability under repeated use, which matters when a salamander is running continuously across a lunch and dinner service.

• Matched to specific Lincat salamander models for a secure, stable fit
• Raises the grill to an ergonomic working height for kitchen staff
• Keeps the installation tidy and consistent with commercial hygiene standards
• Eliminates the need for improvised risers or unsuitable platforms
• Reduces the risk of the unit shifting under sustained heavy use

It is worth confirming your exact salamander model before ordering. This stand is designed for specific units within the Lincat range and will not be a correct fit for other models. If you are configuring a new grill station and want to be certain the combination works for your available bench space and workflow, the team is happy to talk through the setup before you commit to an order.

The Lincat OA8907 is a purpose-built floor stand designed to support specific Lincat salamander grills — namely the OG8301 and OE7303 models. It raises the salamander to a freestanding working height, offering a practical alternative to wall mounting or bench positioning where the building structure, wall construction, or kitchen layout makes fixed wall installation difficult or undesirable.

Salamander positioning has a real effect on service pace and chef comfort. A unit positioned too low or at an awkward angle slows finishing and plating, particularly during a busy pass. This stand brings the grill to a consistent, chef-friendly working height and holds it stable under the repeated daily use a commercial kitchen demands. For kitchens where wall fixings are simply not an option — listed buildings, rented premises, or sites with block or tiled walls that complicate drilling — a floor-standing arrangement is often the most straightforward solution.

• Raises the salamander to a practical, chef-accessible working height
• Compatible specifically with Lincat OG8301 and OE7303 salamander models
• Provides a stable freestanding footprint on the kitchen floor
• Suited to sites where wall mounting is restricted or structurally impractical
• Constructed to meet the hygiene and durability requirements of a commercial food environment

Before ordering, it is worth checking available floor space and confirming how your gas or electrical supply will route relative to where the stand will sit. This is not a universal accessory — it is designed for the two Lincat models listed, so compatibility should always be confirmed before purchase.

If you are weighing up floor-standing against wall-mounted installation for your salamander, or you are unsure which arrangement suits your kitchen setup, we are happy to talk it through before you commit.

This is a genuine Buffalo replacement top heatproof tray, designed specifically for the Buffalo Quartz Salamander Grill (CJ799). It is a like-for-like spare part intended to restore the unit to its original operating condition rather than a universal accessory.

In a busy kitchen, the heatproof tray on a salamander takes sustained punishment — direct radiant heat, grease splatter, and the general wear of continuous service. Replacing it with a genuine part rather than an aftermarket alternative helps ensure the fit, heat tolerance, and safe operation that the original equipment was designed around.

If you are unsure whether this tray is the correct part for your unit, or if you need guidance on other Buffalo salamander spares, we are happy to help you confirm compatibility before you order.

This is the genuine Buffalo replacement crumb tray designed to fit the Buffalo CJ753 salamander grill. It sits beneath the grill's heating zone to collect food debris, fat drips, and carbonised residue that accumulate during normal service — keeping the unit cleaner between deep cleans and reducing the risk of flare-ups or odour build-up during service.

In a busy kitchen, crumb trays take a great deal of heat and daily abuse. Over time they warp, corrode, or simply become too fouled to clean effectively. Having a genuine replacement to hand means you can swap it out quickly without any downtime — particularly useful in high-throughput operations where the salamander runs continuously across multiple services.

• Designed specifically for the Buffalo CJ753 salamander — ensures correct fit without modification
• Collects grease and food debris, reducing flare-up risk during service
• Easy to remove and clean between services
• Replacing a worn tray helps maintain hygiene compliance
• Genuine Buffalo part — consistent quality and accurate fit

This tray is a direct like-for-like replacement and requires no tools or technical knowledge to fit. It is worth keeping a spare in stock if your salamander is in constant use — it is one of those consumable components that is easy to overlook until it fails.

If you are unsure whether this tray is compatible with your specific unit, or if you have an older Buffalo salamander and want to confirm the right part, feel free to get in touch with the team before ordering.

This is the manufacturer-matched top tray for the Buffalo salamander grill range, specifically designed to fit the GF452 and GF453 models, as well as the DB177 and DB183 units. It is a direct replacement part intended to restore the grill to full working condition when the original tray has warped, corroded, or been damaged through heavy service use.

Salamander grills take considerable punishment in a busy kitchen — constant high heat, grease splatter, and daily cleaning cycles all take their toll on the top tray over time. Having a correctly fitted replacement to hand means a grill can be returned to service quickly rather than sitting idle while a fabrication workaround is attempted or a full unit replacement considered.

• Direct fit for GF452, GF453, DB177, and DB183 salamander models
• Maintains correct clearance and heat reflection geometry
• Restores the grill to manufacturer specification
• Suitable for ongoing heavy service use

It is worth confirming your exact model number before ordering, as salamander trays are not universally interchangeable even within the same brand range. If you are unsure which tray corresponds to your unit, the team is happy to help you verify compatibility before you commit to a purchase.

This is the manufacturer's replacement cooking grid for the Buffalo CP240 combi BBQ and griddle unit. It is a direct like-for-like part, intended to restore the cooking surface to its original condition when the existing grid has worn, warped, or become damaged beyond practical cleaning.

In a busy kitchen, cooking grids take considerable punishment — sustained high heat, repeated thermal cycling, heavy food loads, and daily cleaning with abrasive agents all shorten their service life. Replacing the grid rather than the whole unit is the practical route when the rest of the CP240 remains in good working order, and using the correct manufacturer's part ensures the fit, spacing, and heat transfer characteristics match the original design.

A few points worth noting before ordering: this grid is designed specifically for the Buffalo CP240 and will not necessarily be compatible with other models in the range. If you are unsure which part your unit requires, it is worth checking the model number on the unit itself before placing an order, as fitting an incorrect grid can affect performance and may cause uneven cooking or poor contact with the heat source.

If you have any doubt about whether this is the right part for your equipment, or if your CP240 is showing other signs of wear that a grid replacement alone may not resolve, it is worth having a conversation with us before ordering.

The Buffalo Chargrill Stand is a purpose-built floor stand designed specifically to support Buffalo commercial chargrills. Constructed from stainless steel throughout, it provides a stable, robust base that keeps the chargrill at a practical working height, reducing operator strain during long service periods.

In a busy kitchen environment, having a chargrill at the correct height matters more than it might seem. Too low and operators are hunched over hot equipment for hours; too high and control becomes awkward. This stand addresses that by raising the unit to a comfortable cooking position, which makes a genuine difference over the course of a full service.

From a practical standpoint, the stainless steel construction is well suited to commercial kitchen conditions — it handles heat, grease, and repeated cleaning without degrading. The open frame design also makes it straightforward to wipe down and keep hygienic, which is a consideration in any kitchen operating under inspection.

• Raises the chargrill to an ergonomic working height for long service periods
• Stainless steel build withstands commercial kitchen heat and cleaning regimes
• Designed specifically to pair with Buffalo professional chargrills
• Open frame construction makes cleaning and maintenance straightforward

This stand is suitable for any operation running a Buffalo chargrill that would benefit from a freestanding setup rather than a countertop arrangement. It is particularly useful where the chargrill forms a dedicated station on the cooking line. It is worth confirming compatibility with your specific Buffalo chargrill model before ordering, as stand dimensions are matched to particular units.

If you are unsure whether this stand suits your chargrill model or kitchen layout, the team is happy to check before you commit to an order.

This is the manufacturer's replacement cooking grid for the Buffalo DR826 BBQ grill. It is a direct like-for-like replacement part, intended to restore the cooking surface of the DR826 unit when the original grid has worn, warped, or become damaged through regular commercial use.

Cooking grids on commercial BBQ units take considerable punishment during busy service periods — repeated high-heat cycles, heavy product loads, and frequent cleaning all contribute to gradual deterioration. Having a genuine replacement to hand reduces downtime when the original grid reaches the end of its serviceable life.

This grid is designed specifically for the DR826 model. Compatibility with other Buffalo BBQ units is not confirmed, so it is worth verifying the model number of your existing equipment before ordering.

If you are unsure whether this is the correct part for your unit, or if you need guidance on maintaining your BBQ grill for extended service life, we are happy to help — just get in touch with the team.

The Buffalo Ceramic Kamado Grid Gripper is a purpose-made handling tool designed to let operators safely lift, remove, or reposition the hot cooking grid on the Buffalo Ceramic Kamado BBQ (DR826) without risk of burns or fumbling with cloths and improvised tools. It is a simple, single-purpose accessory rather than a complex piece of equipment, but in a live service environment it plays a practical role in keeping things moving safely.

When working with a kamado-style cooker at high temperatures, direct contact with the cooking grid is genuinely hazardous. Having the correct grip tool to hand means grids can be repositioned quickly during cooking — whether to add fuel, adjust airflow, or clear the cooking surface — without interrupting service or risking injury.

• Designed specifically to fit the Buffalo DR826 Ceramic Kamado BBQ
• Allows safe handling of hot grids without the need for cloths or oven gloves
• Supports quick grid removal during live cooking and service
• Reduces the risk of burns when adjusting or cleaning the cooking surface
• Compact and easy to store alongside the unit

This gripper is designed for use with the Buffalo DR826 model. If you are unsure whether it is compatible with your existing setup, or if you are putting together a full kamado accessory kit, the team is happy to advise before you order.

This is the manufacturer-matched replacement grilling rack for the Buffalo L508 Pro Toaster Griller. It is a direct spare part intended to restore or maintain the unit's original grilling function, ensuring the rack fits and performs as the machine was designed to operate.

In a busy catering environment, grilling racks take considerable wear — repeated high-heat cycles, heavy manual handling during cleaning, and the general demands of service all shorten the working life of contact components. Having the correct replacement part to hand avoids unnecessary downtime when a rack becomes damaged or worn beyond use.

Using the OEM-matched rack rather than a generic alternative helps maintain consistent contact with the heating elements and ensures the food sits at the correct distance for even browning and thorough heating — both of which matter in a professional kitchen where output quality needs to be repeatable across service.

This rack is specific to the Buffalo L508 Pro Toaster Griller and is not a universal fitting. Before ordering, it is worth confirming your unit's model reference to avoid an incompatible part arriving on site.

If you are unsure whether this is the right component for your machine, or if you are looking at replacing the griller unit itself, the team is happy to point you in the right direction.

This is a genuine replacement crumb tray for the Buffalo salamander grill range, compatible with models GF452 and GF453. It sits beneath the grill zone to catch food debris, fat drips, and carbonised residue during service, keeping the interior of the unit clean and reducing the risk of flare-ups or excess smoke.

In a busy kitchen, a crumb tray takes consistent punishment — repeated heating cycles, grease build-up, and frequent removal for cleaning. Having a serviceable spare on hand avoids any interruption to the grill when the original tray needs replacing or is out of action during a deep clean.

Keeping a clean crumb tray in place also supports hygiene compliance and helps maintain consistent grill performance, as accumulated debris can affect heat distribution over time. Replacement is straightforward and requires no tools.

If you are unsure whether this tray is the correct fit for your unit, or if you need further spares for your Buffalo salamander, our team is happy to help you confirm compatibility before you order.

This is a genuine replacement handle for the drip tray on the Buffalo CP240 combi BBQ and griddle unit. If the original handle has been lost, damaged, or has deteriorated through heavy use, this part restores safe and practical access to the drip tray during and after service.

Keeping the drip tray handle in good working order is a straightforward but important maintenance consideration. A missing or broken handle makes drip tray removal awkward and increases the risk of spillage or burns, particularly during a busy service period. Replacing it promptly keeps the unit operating safely and hygienically.

If you are unsure whether this handle is the correct fit for your unit, or if you need guidance on other Buffalo CP240 replacement parts, our team is happy to help you confirm compatibility before you order.

This is the genuine Buffalo replacement crumb tray designed specifically for the Buffalo Quartz Salamander Grill, model CJ799. It sits beneath the grill to collect food debris, carbonised residue, and grease drips that accumulate during normal service — keeping the unit cleaner and reducing the risk of build-up that can affect performance or create a fire hazard over time.

In a busy kitchen, crumb trays take a significant amount of daily punishment. Repeated high-heat cycles, grease exposure, and routine cleaning can cause warping or damage to the original tray over time. Having a genuine replacement to hand means you can swap it out quickly without interrupting service or compromising hygiene standards.

• Genuine Buffalo part — correct fit for the CJ799 model
• Collects debris and grease drips to protect the grill interior
• Supports routine cleaning and maintenance between services
• Reduces fire risk from accumulated carbonised residue
• Simple swap-out with no tools or specialist knowledge required

This tray is a direct replacement and fits the CJ799 only. If you are unsure whether this is the correct part for your unit, it is worth checking your salamander's model number before ordering, as Buffalo produces several salamander variants and trays are not always interchangeable between models.

If you need help confirming compatibility or want to discuss a maintenance schedule for your Buffalo equipment, the team is happy to assist.

This is the manufacturer's replacement drip pan for the Buffalo combi BBQ and griddle unit, compatible with the CP240 model. Its purpose is straightforward: to collect fat, grease, and food debris that falls away from the cooking surface during use, keeping the unit clean and reducing the risk of flare-ups or build-up beneath the griddle plate.

In a busy kitchen, drip pans on combination grill and griddle units take a significant amount of punishment. Regular exposure to high heat, heavy grease loads, and frequent emptying means they wear out or become damaged over time. Having a direct replacement to hand avoids unnecessary downtime when the existing pan warps, corrodes, or is no longer serviceable.

• Direct replacement part — fits the Buffalo CP240 combi BBQ and griddle
• Collects grease and debris during cooking to keep the unit clean
• Straightforward to remove, empty, and refit between services
• Helps maintain safe operating conditions by managing grease accumulation
• Keeps the unit running as intended without improvised alternatives

This part is specifically matched to the CP240. If you are unsure whether this pan fits your model, or if you are looking for other Buffalo service parts, it is worth checking with the team before ordering to avoid a return.

This is a replacement drip tray designed to fit the Buffalo P108 and P109 countertop griddles. It sits beneath the cooking surface to collect fat and food residue during service, helping to keep the surrounding worksurface clean and reducing the risk of grease build-up around the unit.

Keeping a spare drip tray on hand is a practical consideration in any busy kitchen — swapping trays during service allows for quick cleaning without taking the griddle offline for extended periods. If the current tray has become damaged or warped through heavy use, replacing it promptly helps maintain safe operating conditions and supports the longevity of the griddle itself.

If you are unsure whether this tray is compatible with your specific griddle or need to confirm the right part for your setup, feel free to get in touch with the team before ordering.