San Jamar Cup Dispensers

The San Jamar XC2226 is a replacement gasket kit designed specifically for San Jamar C2210 series cup dispensers. The kit contains four gaskets covering small, medium, large, and extra-large cup sizes, making it a practical stock item for any operation running C2210 dispensers across a range of cup formats.

In a busy front-of-house or beverage service environment, cup dispenser gaskets are a consumable component. Over time and with regular use, they can wear, distort, or lose their tension, causing cups to drop too freely or sit too tight — both of which slow down service and frustrate staff. Keeping a spare kit to hand means a worn gasket can be swapped out quickly without taking the dispenser out of service for longer than necessary.

The XC2226 kit is straightforward to fit and does not require tools or specialist knowledge. It is well suited to operations that run multiple C2210 dispensers, or where high throughput puts additional wear on components. Sites such as staff canteens, quick-service restaurants, cafeterias, and leisure facilities that rely on cup dispensers throughout the day will find this a sensible addition to their maintenance supplies.

It is worth confirming that your dispensers are C2210 models before ordering, as gasket kits are not universal across the San Jamar range. If you are unsure which gaskets are compatible with your existing dispensers, the team is happy to help you check before you order.

The San Jamar C4180TBLW is a wall-mounted or surface-mounted water cup dispenser designed for small flat-bottom and cone-style cups in the 57–73mm diameter range. It is a straightforward, pull-type dispenser built for high-frequency use in self-service or staff-facing beverage stations.

In practice, these dispensers are commonly found at water cooler stations, patient areas, staff canteens, and waiting areas where a steady throughput of single-use cups is needed throughout the day. The self-adjusting mechanism accommodates a reasonable range of cup sizes without manual reconfiguration, which reduces the small operational nuisances that come with mixed cup stock.

Key practical advantages include:

• Transparent tube allows cup levels to be checked at a glance, reducing the chance of running out during busy periods
• Flip cap keeps stored cups covered and hygienic between refills
• Pull-type dispensing delivers one cup at a time, minimising waste and contact with remaining stock
• Mounting bracket suits both flat-wall installation and attachment to cooler units
• Arctic Blue finish makes the unit straightforward to locate in a busy service area

Installation is simple — the unit mounts to any flat vertical surface using the supplied bracket and requires no power or water connection. It is worth confirming cup compatibility before ordering, as not all small cups fall within the 57–73mm throat range. For locations with very high footfall or where a larger cup format is in use, a higher-capacity or differently sized dispenser may be a more practical choice.

This model is well suited to lower-volume self-service points, water cooler stations, reception areas, and staff facilities. It is less suited to high-volume production environments where a larger-format or multi-position dispensing solution would be more appropriate.

If you are unsure whether this unit matches your cup stock or installation setup, the team is happy to help you confirm compatibility before you order.

The San Jamar Euro EZ-Fit is an in-counter cup dispenser designed to sit flush within a countertop cut-out, presenting cups at surface level for clean, one-at-a-time dispensing. It handles paper, plastic, and foam cups across a rim diameter range of 73–94mm, with interchangeable gaskets allowing operators to switch between cup sizes without replacing the unit itself.

In a café, bar, or quick-service counter environment, keeping the worktop clear is a genuine operational advantage. The in-counter format removes the dispenser from the working surface entirely, which reduces clutter and makes the counter easier to wipe down during service. One-at-a-time dispensing helps prevent double-pulls and the cup waste that tends to accumulate over a busy shift. Staff can retrieve a cup quickly without disturbing the stack, which keeps pace steady during peak periods.

• Accepts paper, plastic, and foam cups within the 73–94mm rim diameter range
• Interchangeable gaskets allow cup format changes without a new unit
• Flush in-counter installation removes the dispenser from the working surface
• One-at-a-time dispensing reduces double-pulls and cup waste
• Impact-resistant construction suited to regular front-of-house use

Installation requires a cut-out in the countertop to the correct diameter. Before ordering, it is worth confirming that your counter has sufficient depth below the surface to accommodate the dispenser body and a full cup stack. Counter thickness and the clearance available underneath are the two details most commonly overlooked at the point of purchase.

This model suits cafés, coffee shops, bars, and quick-service counters with moderate cup throughput and limited counter space. For very high-volume sites dispensing cups continuously throughout the day, a larger-capacity or higher-throughput unit may be a more appropriate fit.

If you would like to talk through whether this dispenser works with your counter setup or cup specification, the team is happy to help before you commit to an order.

The San Jamar C5250C Euro Sentry is an in-counter cup dispenser designed to sit flush within a counter or serving surface, presenting cups at counter level for clean, controlled dispensing. It accommodates a wide rim diameter range, making it compatible with a broad selection of standard disposable cups commonly used in cafés, canteens, hospital catering, and self-service beverage stations.

In busy service environments, the dispenser's elevator mechanism advances cups automatically as each one is removed, maintaining a consistent presentation without staff intervention. The adjustment mechanism can be set while cups are loaded, which reduces downtime during service if cups are changed between shifts or when switching cup sizes. The dispenser is designed to release one cup at a time, preventing the double-dispensing waste that tends to accumulate over a full service period.

From an operational standpoint, several features make this unit well suited to managed service and food safety-conscious environments:

• Contamination Guard helps prevent debris and airborne particles from entering the tube
• Food Safety Blue transparent tube allows a quick visual check of cup stock and cleanliness without disassembly
• Adjustable levers engineered to avoid marking or deforming cups during dispensing or loading
• Trim ring discourages tampering in self-service settings
• Tool-free adjustment is possible with cups already loaded, reducing service interruption

Installation requires a cut-out in the counter surface to the appropriate diameter. The unit drops into position and is held by the trim ring, so the counter surface material and thickness should be considered before ordering. No electrical or water connection is required.

This dispenser is a practical choice for self-service beverage points, front-of-house counters, and staff canteens where hygiene, neat presentation, and minimal maintenance are priorities. It suits moderate-volume sites well. For very high-throughput operations running multiple cup sizes or dispensing points simultaneously, it is worth discussing whether a different configuration would serve better.

If you are unsure whether this unit is the right fit for your counter setup or cup range, we are happy to talk it through before you order.

The San Jamar C3400CF is a counter-mounted cup dispenser designed to hold and present 12 to 24oz cups at an angled position above the worktop. It is built for front-of-house beverage stations, self-service counters, and staffed service points where accessible, consistent cup dispensing is needed throughout the day. Construction is in 304 stainless steel, which holds up well in wet service environments and tolerates the cleaning routines typical of commercial counter use.

Where this model differs from simpler collar-style dispensers is the patented adjustable collar, which allows the unit to be set for different cup rim profiles without replacing any major components. Interchangeable springs let operators match dispensing tension to the cup material in use, which helps prevent jamming or double-dispensing during a busy service period — a common frustration with fixed-tension dispensers when cup stock changes between deliveries.

The main operational advantages are worth noting directly:

• Adjustable collar accommodates varying rim diameters across the 70–98mm range
• Interchangeable springs allow tension to be matched to cup weight and material
• Patented mounting ring fixes securely to the counter surface without under-counter support
• Angled orientation keeps cups within easy reach at the service point
• Stainless steel construction suits regular cleaning and damp counter environments

Installation requires no under-counter cavity. The mounting ring fixes to the counter surface and supports the dispenser tube above the worktop, which makes this a practical option where a fully recessed in-counter dispenser is not possible due to counter depth or construction. It is worth confirming cup compatibility before ordering, as not all cup profiles within the stated diameter range will dispense equally well with every spring combination.

This dispenser suits cafés, quick-service operations, canteens, and hospitality venues where a reliable, low-maintenance cup dispensing point is needed at counter level. For sites running very high cup volumes across multiple service points, a higher-capacity or in-counter alternative may be worth considering.

If you want to talk through cup compatibility or whether this unit suits your counter setup, the team is glad to help before you place an order.

The San Jamar C2901 is a surface-mounted single cup dispenser cabinet designed for countertop beverage stations where cutting into the counter is not practical or permitted. It houses a single EZ-Fit cup dispenser and is intended for operations that need tidy, accessible cup dispensing at a fixed service point without a permanent in-counter installation.

In a working service environment, the cabinet keeps cups protected, upright, and dispensed one at a time, reducing the risk of cups being knocked over, contaminated by handling, or taken in multiples. The EZ-Fit dispenser uses interchangeable pre-cut gaskets, which means the same unit can be adjusted to suit different cup sizes across a wide range — covering most standard paper, plastic, and foam beverage cups from around 8oz through to 46oz. This makes it reasonably flexible for operations that occasionally change cup sizes or run different cups at different service points.

• One-at-a-time dispensing reduces cup contamination and waste
• Four interchangeable gaskets accommodate a wide range of cup sizes without replacing the dispenser
• Surface-mounted design suits counters where in-counter fitting is not possible
• Compatible with paper, plastic, and foam cups across most standard sizes
• Black polystyrene cabinet construction keeps cups enclosed and presentable at the point of service

Installation is straightforward — the cabinet is designed for countertop placement or surface mounting and does not require plumbing, electrical connection, or any specialist trade work. It is worth confirming the cup rim diameter against the gasket range before ordering, as the fit depends on selecting the correct gasket for the cup in use.

This cabinet is well suited to cafés, quick-service restaurants, staff canteens, healthcare catering, and similar settings where a single cup size or a small range of cup sizes is dispensed at a fixed point. For operations running multiple cup sizes across a busy service counter, a multi-position or higher-capacity cabinet configuration may be worth considering.

If you are unsure whether this unit suits your cup sizes or service setup, the team is happy to talk it through before you order.

The San Jamar C4160WH is a wall- or cooler-mounted pull-type dispenser designed to hold and dispense small flat-bottom and cone water cups in the 57–73mm diameter range. It is a straightforward, practical piece of front-of-house or breakroom kit that keeps cups protected, orderly, and easy to access without handling the cup rim.

In busy service environments — waiting areas, staff canteens, hospital corridors, or alongside water coolers in office kitchens — dispensers like this earn their keep by keeping cups clean and reducing the kind of handling that creates hygiene concerns. The flip cap keeps the cup stack covered between refills, and the transparent tube body lets staff see at a glance when the dispenser needs topping up, avoiding the situation where a cup stack runs out unnoticed during a busy period.

From an operational standpoint, the main practical advantages are:

• Flip cap protects cups from dust, splashing, and incidental contact
• Transparent tube allows quick visual stock checks without opening the unit
• Self-adjusting design accommodates both flat-bottom and cone cup formats
• Mounting bracket suits water coolers or any flat vertical surface
• Refilling is straightforward and does not require tools or removal of the unit

Installation is simple — the unit mounts via a bracket to a wall or directly to a water cooler. No electrical or plumbing connections are required. It is worth confirming your cup diameter sits within the 57–73mm range before ordering, as San Jamar produce dispensers in several size formats to suit different cup stocks. If you are equipping multiple locations or need a larger-capacity or stainless-finished version, there are alternatives within the range worth considering.

This dispenser is well suited to lower-volume settings: office kitchens, waiting rooms, small staff canteens, and any position alongside a water cooler where a clean, contained cup supply is needed. It is less appropriate for high-throughput hospitality or healthcare settings where a higher-capacity or more robust unit would be more practical.

If you are unsure which size or finish best suits your cup stock and location, the team is happy to point you in the right direction before you order.

The San Jamar C3200EV is a vertical, surface-mounted dispenser for cups in the 6 to 10oz (180 to 300ml) range, with rim diameters of 56 to 81mm. It is built for fixed installation at beverage stations, self-service areas or behind counters, wherever you want cups presented cleanly and consistently through service. The body is 304 stainless steel, which stands up to regular cleaning and wipe-downs.

It suits moderate-volume sites where cups are drawn steadily rather than in rapid bursts. The adjustable collar is the key part: it is set to the rim diameter of the cup you use, which reduces the chance of several cups coming out at once or jamming. It is worth taking time to set the collar correctly for your cup stock during installation.

• Keeps cups enclosed and protected from handling contamination
• Frees up counter space compared with open cup stacking
• Single-cup dispensing reduces waste during busy service
• 304 stainless steel construction wipes clean quickly
• Vertical mounting keeps the footprint compact at the point of use

Fit it to a flat surface or wall with enough clearance to load cups from below. The dispenser is fixed in place, so choose a mounting position with refilling in mind, as an awkward location makes restocking slower than it needs to be. Check that your cup rim diameter falls within 56 to 81mm before ordering.

Suited to cafés, staff canteens, waiting areas and self-service beverage stations with moderate throughput. For higher-volume sites, larger cup formats, or where a freestanding or countertop unit is needed, another configuration may suit better.

If you are unsure whether this model fits your cups or setup, call 01304 827272 and we will help you work through the options.

The San Jamar C3200CH is a horizontal counter-mount cup dispenser designed to hold and present 6 to 10oz cups at a fixed, accessible position on a beverage counter or service station. It mounts securely to the counter surface, keeps cups contained and hygienic, and delivers them one at a time through a spring-loaded mechanism. It is a straightforward, practical piece of equipment commonly found at café beverage counters, quick-service drink stations, and self-service points.

In a working service environment, having cups stored loose on a counter creates handling delays and hygiene risks. A mounted dispenser keeps the cup stack contained, presents each cup cleanly to staff or customers, and removes the fumbling that comes with grabbing from an open stack during a busy period. The adjustable collar on this model accommodates a range of cup rim diameters, which gives operators some flexibility if cup suppliers change or cup styles vary across the site.

• Adjustable collar fits different cup diameters within the supported range
• Spring-loaded delivery reduces double-dispensing during fast-paced service
• Counter-mount ring holds the unit firmly in place under repeated use
• Stainless steel construction is straightforward to clean and maintain
• Horizontal orientation suits counter runs where overhead clearance is limited

Installation requires no electrical connection or plumbing — the unit mounts directly to the counter surface. Before ordering, it is worth confirming that your cup rim diameter falls within the supported range and that a horizontal counter-mount orientation suits your counter layout. For environments with very high cup throughput or where an in-counter or wall-mounted configuration would work better, there are alternative mounting styles available.

This dispenser is well suited to cafés, beverage counters, canteens, and self-service areas handling moderate to steady cup volumes. If you are weighing up mounting options or want to confirm compatibility with your current cups, the team can help you work through it.

The San Jamar C5450C Sentry is an in-counter cup dispenser designed for front-of-house beverage stations, self-serve drink areas, and cafeteria counters where neat, hygienic cup presentation matters. It fits flush into a counter cutout and holds a column of cups in a protected tube, dispensing one cup at a time from the bottom. The unit is compatible with cups in the 79–114mm rim diameter range, which covers a broad spread of standard catering cups.

In busy service environments, the value of a well-designed cup dispenser is easy to underestimate. A poor dispenser jams, dispenses two at a time, or leaves cups exposed to the counter environment. The Sentry addresses these issues directly. The adjustable lever mechanism — San Jamar's Lifetime Lever system — is engineered to release a single cup cleanly without marring the rim or sides, which matters particularly where cups are going directly into customers' hands. Adjustment is possible even with the dispenser loaded, so staff do not need to empty it to recalibrate for a different cup batch.

From an operational standpoint, the practical advantages include:

• One-at-a-time dispensing reduces waste and prevents customers taking multiples
• Contamination Guard keeps the cup stack protected from airborne debris and counter spillage
• Food Safety Blue transparent tube allows a quick visual check of cup levels without opening the unit
• Trim ring finish integrates cleanly into counter surfaces and discourages customer interference with the mechanism
• Tool-free lever adjustment simplifies changeover when switching cup sizes

Installation requires a counter cutout sized to accept the 23.5-inch tube. It is worth confirming counter depth and material before ordering, as the unit sits proud of the underside and needs adequate clearance below. This dispenser suits lighter to moderate service volumes — higher-footfall sites running very large cup counts may benefit from a gravity-feed or higher-capacity model.

This model is well suited to cafés, hotel breakfast stations, staff canteens, and self-serve drink counters where a tidy, hygienic cup presentation is a priority. If you are fitting out multiple stations or are unsure which rim diameter range matches your current cup stock, it is worth having a conversation with us before ordering.

The San Jamar C4200PF is a wall-mounted, pull-type cup dispenser constructed from high-impact stainless steel and designed to hold foam beverage cups in the 4 to 10oz range. It is a straightforward piece of front-of-house or self-service kit — cups are loaded from the top and dispensed individually by pulling from the base, keeping the stack clean and accessible throughout service.

In a busy café, canteen, or beverage station, this type of dispenser earns its place by keeping cups organised, hygienic, and within easy reach without occupying counter space. The self-adjusting mechanism accommodates the range of foam cup sizes without requiring separate sizing rings, which is useful where a site uses more than one cup format across hot and cold drinks. The stainless steel construction is durable enough for frequent daily use and straightforward to wipe down as part of a routine hygiene check.

• Top-loading gravity-fed design with protective cap keeps cups clean between refills
• Self-adjusting sleeve fits foam cups across the 4–10oz range without adaptors
• Wall or cooler-mounted to free up counter space at busy service points
• Stainless steel tube resists impact and cleans down easily
• Removable cap allows quick, hygienic refilling during service

Installation is straightforward — the unit fixes to most wall surfaces or cooler sides using standard fixings, making it suitable for countertop beverage stations, self-service areas, or staff refreshment points. No electrical or plumbing connections are required. It is worth confirming that your foam cup stock falls within the 70–85mm rim diameter range before purchasing, as the dispenser is sized for that profile.

This dispenser suits cafés, canteens, healthcare catering, convenience stores, and any site running a self-service hot or cold drinks station with moderate to high cup throughput. If you're fitting out a larger or higher-volume station and need to consider multiple dispensers or a different mounting configuration, the team are happy to help you work out what suits the space.

The San Jamar C4410PFSD is a wall-mountable, pull-type foam cup dispenser designed to hold and dispense 12 to 24oz foam beverage cups in a controlled, hygienic way. It is a straightforward piece of front-of-house or beverage station kit — cups are loaded from the top and dispensed one at a time from the base, keeping the stack protected and the service point tidy.

In practice, this type of dispenser earns its place at self-serve drink stations, hot beverage counters, and cooler fronts where staff or customers need quick, single-cup access without handling the whole stack. The self-adjusting mechanism accommodates the common range of foam cup sizes without requiring separate sizing rings, which reduces the fuss of switching between cup formats if your supplier changes batch dimensions slightly.

From an operational standpoint, the main advantages are straightforward:

• Frees up counter space by moving cups off the worktop and onto the wall or cooler face
• Protects cups from dust and handling via the gravity-fed, top-loading design with a removable flip cap
• Eliminates sizing ring changes across standard foam cup sizes in the 12-24oz range
• High-impact plastic construction holds up to frequent daily use without cracking or warping

Installation is minimal — the unit attaches to most wall surfaces and cooler fronts without specialist tools or trades involvement. There are no electrical, water, or gas connections required. The main practical consideration is positioning: mount it at a height that suits your service flow, and ensure the cup size you use regularly falls within the supported rim diameter range before ordering.

This dispenser is well suited to cafés, canteens, convenience counters, and self-serve beverage stations handling moderate daily cup volumes. For very high-throughput sites dispensing several hundred cups per session, a higher-capacity model or a countertop unit may be worth considering.

If you are unsure whether this unit suits your cup format or station layout, our team are happy to help you confirm the right fit before you order.

The San Jamar C3165WH is a wall- or cooler-mounted pull-type cup dispenser designed for water stations in commercial and public-facing environments. It accepts a range of flat-bottom and cone water cups in the 64–83mm diameter range, dispensing one cup at a time via a simple pull mechanism that keeps remaining cups clean and contained.

In practice, this type of dispenser is commonly used alongside water coolers, self-service drink stations, and staff welfare points in kitchens, offices, healthcare settings, and hospitality back-of-house areas. The flip cap protects stored cups from airborne contamination and makes restocking straightforward without fully dismantling the unit. The transparent tube allows staff to check cup levels at a glance, reducing the chance of running dry during a busy period.

From an operational standpoint, the practical advantages are straightforward:

• Single-cup dispensing reduces waste and avoids cups being grabbed in multiples
• Flip cap keeps cups hygienic between restocks
• Clear tube body allows quick visual stock checks without opening the dispenser
• Mounting bracket suits flat surfaces and standard water cooler necks
• Self-adjusting mechanism accommodates both flat-bottom and cone cup styles

Installation is simple — the bracket mounts directly to a cooler or any flat vertical surface using the supplied fittings. No electrical or water connections are required. The unit is best positioned at an accessible height for the end user and within easy reach for restocking staff. It is suited to low-to-medium footfall locations; for high-volume sites dispensing large quantities throughout the day, a higher-capacity model may be worth considering.

This dispenser is well suited to small catering operations, staff welfare points, waiting areas, or any location where a neat, hygienic single-cup solution is needed without significant infrastructure. If you are equipping multiple stations or need guidance on cup compatibility, the team is happy to help before you order.

The San Jamar C3400EV is a vertical, surface-mounted dispenser for cups in the 12 to 24oz (350 to 710ml) range, with rim diameters of 70 to 98mm. It mounts to a wall, under a counter or at the end of a beverage station, which frees up worktop space and keeps cups within reach at the point of use. The body is 304 stainless steel, which copes well with the damp, busy conditions around drinks stations.

Cups are presented one at a time, so staff and customers are less likely to pull out several at once. In a high-footfall operation that saves a surprising amount of waste. The adjustable collar can be set for different rim diameters within the supported range, so one unit suits a station that handles more than one cup size.

• Surface-mount design keeps counters clear and cups close to hand
• Adjustable collar fits cup rim diameters from 70 to 98mm
• 304 stainless steel construction wipes clean quickly and stands up to daily service
• One-at-a-time dispensing cuts down on over-grabbing and wasted cups
• No power or water connection needed, mounts with standard fixings

Check your cup rim diameter falls within 70 to 98mm before ordering, as the collar adjustment has limits. Mounting height matters too: whether staff or customers use the dispenser will affect where it sits most comfortably on the wall or counter end.

Suited to cafés, canteens, hotel beverage points and self-service areas serving hot or cold drinks. For much higher volumes, or where a recessed installation is needed, a different format may suit better.

If you'd like us to check your cup specification against this unit before you order, call 01304 827272 and we'll confirm the fit.

The San Jamar C4500PF is a surface-mounted, pull-type dispenser designed to hold large-format foam beverage cups in the 32 to 46oz range. Cups are top-loaded into a stainless steel tube and dispensed one at a time from the base — a gravity-fed mechanism that is straightforward to operate and easy to restock mid-service without interrupting the flow of a busy counter.

The self-adjusting sleeve is a practical detail worth noting. Foam cups can vary slightly in diameter between batches and suppliers, and the sleeve accommodates that variation without needing separate sizing rings or adjustment. For sites that refill dispensers frequently or source cups from more than one supplier, this removes a small but genuine operational inconvenience. The stainless steel tube construction handles the repeated handling and incidental knocks typical of high-footfall service points, and the removable flip cap keeps the cup stack protected from dust and airborne contaminants between refills.

• Self-adjusting sleeve fits foam cup batches without additional parts or tools
• Pull-type dispensing limits cup contact, supporting front-of-house hygiene
• Top-loading design allows fast restocking without removing the unit
• Mounts to wall surfaces or upright cooler panels to free up counter space
• Stainless steel tube withstands regular handling in busy service environments

Fitting is uncomplicated — the unit mounts to most standard wall surfaces or cooler uprights using the supplied hardware, with no electrical or plumbing connections required. Before ordering, it is worth confirming that your cup stock falls within the supported rim diameter range, as foam cup dimensions can vary between manufacturers.

This dispenser is a practical choice for fast food outlets, convenience stores, cinema and leisure concessions, self-service canteens, and anywhere large cold drink cups are in consistent, high-volume use. Sites dispensing smaller cup formats, or those needing a countertop rather than wall-mounted configuration, will find alternative options within the wider range.

If you want to confirm compatibility with your existing cup stock before placing an order, the team is glad to help you work through that.

The San Jamar C3165TBL is a wall or surface-mountable pull-type water cup dispenser designed for medium-sized flat-bottom and cone cups in the 64–83mm diameter range. The dispenser uses a simple pull-through mechanism that allows customers or staff to retrieve a single cup cleanly, without touching adjacent cups. The Arctic Blue finish makes it a practical choice where hygiene visibility and a tidy service point matter.

In a busy self-serve or staffed beverage station, reliable cup dispensing is often overlooked until it causes a problem. This unit keeps cups contained, protected, and consistently accessible throughout service. The transparent tube allows staff to monitor cup levels at a glance without interrupting service to investigate, and the flip cap keeps the cup stack covered between refills, reducing the risk of contamination from airborne debris or handling.

The practical benefits for a working operation include:

• Self-adjusting mechanism accommodates a range of compatible medium cup sizes
• Transparent tube gives instant visibility of remaining cup stock
• Flip cap protects cup stack and simplifies refilling without full disassembly
• Impact-resistant plastic construction holds up in high-traffic service environments
• Mounting bracket suits countertop coolers or any flat wall or surface

Installation is straightforward — the included mounting bracket allows the unit to be fixed to a flat surface or positioned on a cooler. No tools or specialist fitting are required beyond basic surface fixing. It is worth confirming cup compatibility before ordering, as the dispenser is sized for medium cups within the stated diameter range and will not reliably accommodate cups outside that specification.

This dispenser is well suited to cafés, canteens, healthcare facilities, leisure sites, and any operation running a self-serve drinks station where hygiene and tidiness at the point of service are a priority. For very high-volume sites dispensing larger cup formats, a higher-capacity or different-sized model may be more appropriate.

If you're unsure whether this unit suits your cup range or station setup, our team is happy to help you confirm the right fit before you order.

The San Jamar C3400CH is a counter-mounted cup dispenser designed to hold and dispense 12 to 24oz cups in a horizontal orientation. It sits on or through a counter surface, keeping cups within easy reach at beverage service points without occupying open counter space. It is compatible with cups in the 70 to 98mm rim diameter range, which covers a broad range of standard paper and plastic cup sizes commonly used in cafés, self-service stations, and front-of-house catering environments.

The spring-loaded mechanism advances cups as each one is removed, delivering consistent single-cup dispensing without staff needing to handle the stack. In busier service periods this matters — fumbling with loose cups slows down the counter and undermines hygiene. Keeping the stack enclosed also limits dust exposure and incidental contact, which is a practical consideration at any front-of-house drinks point.

• Adjustable collar accommodates different cup profiles within the supported rim range
• Spring mechanism delivers clean, single-cup dispensing at pace
• Counter-mount installation keeps the drinks station tidy and cups consistently accessible
• Stainless steel construction withstands daily cleaning routines without deterioration
• Locking ring secures the unit firmly to the counter during busy service

Installation does not require specialist tools — the dispenser mounts to the counter surface and the locking ring holds it securely in place. Before ordering, it is worth confirming the rim diameter of your specific cups, as compatibility depends on this. The adjustable collar gives some flexibility within the stated range, but it will not bridge a significant mismatch. For operations running multiple beverage points at high volume, a wall-mounted or multi-tube arrangement may be worth considering instead.

This dispenser is well suited to small to medium cafés, hotel beverage counters, self-service drink stations, and catering setups where a tidy, accessible cup point is needed without a complex installation. If you are unsure whether it will work with your cup size or counter configuration, our team is happy to help you confirm before you order.

The San Jamar C2410C is an in-counter cup dispenser designed to sit flush within a counter cut-out, storing cups below the worktop and presenting them at the rim for clean, one-at-a-time dispensing. It accepts paper, plastic and foam cups across a broad rim diameter range, and the EZ-Fit name refers to a practical interchangeable gasket system — four pre-cut gaskets are included, allowing the unit to be reconfigured for different cup sizes without replacing the dispenser itself.

In a working beverage station, keeping cups stored below the counter makes a meaningful difference to surface organisation. Cups stay protected from airborne contamination and incidental contact, while remaining accessible to staff or self-serve customers without unnecessary handling. The impact-resistant construction holds up well in the repetitive, daily-use conditions of a commercial environment.

• Interchangeable gaskets allow cup size changes without replacing the unit
• Flush in-counter fit keeps the worktop clear and the service point tidy
• Compatible with paper, plastic and foam cup formats
• Single-handed dispensing reduces contact and supports hygiene at self-serve points
• Straightforward gasket changeover requires no specialist tools

Installation requires a counter cut-out sized to the dispenser's footprint. Before fitting, it is worth confirming counter thickness and material to ensure a clean, secure installation. The rim diameter range of 73 to 121mm suits most standard cup formats, but it is worth checking this against your current cup stock before ordering. For operations using cups outside this range, or where a higher-capacity tube is needed to reduce refill frequency, other configurations exist within the San Jamar range.

This dispenser is well suited to cafés, food-to-go counters, staff canteens, and self-service beverage stations where a clean, organised cup point matters. If you are setting up a new station or are unsure which dispenser configuration fits your cup format and counter setup, we are happy to talk it through with you.

The San Jamar C4400PF is a wall or cooler-mounted pull-type dispenser designed to hold foam beverage cups in the 12 to 24oz range. It operates on a gravity-fed, top-loading principle — cups are loaded from the top and dispensed one at a time by pulling from the base. The stainless steel tube construction gives it a clean, professional appearance that suits front-of-house and back-of-house environments alike.

In busy service settings, consistent cup dispensing matters more than it might seem. Having cups readily accessible without staff needing to handle a full sleeve reduces contact, speeds up service, and keeps the counter area tidier during peak periods. The self-adjusting mechanism accommodates the full 12 to 24oz foam cup range without requiring separate sizing rings, which simplifies restocking when cup sizes change between service periods or across different beverages.

• Self-adjusting fit across the full 12–24oz foam cup range without sizing rings
• Gravity-fed top-load design makes refilling quick and straightforward
• Removable flip cap protects stored cups from airborne contaminants
• High-impact stainless steel tube construction handles frequent daily use
• Mounts to most wall surfaces and cooler sides to free up counter space

Installation is straightforward — the unit attaches to most standard wall surfaces or cooler exteriors using the included mounting hardware. There are no electrical or plumbing requirements. It is worth confirming the rim diameter of your specific foam cups falls within the 82 to 98mm range before ordering, as foam cup dimensions can vary between manufacturers even within the same nominal fluid ounce size.

This dispenser is well suited to cafés, canteens, self-service counters, convenience-style beverage stations, and anywhere foam cups are dispensed at moderate to high volume. For very high-throughput sites dispensing multiple cup sizes simultaneously, a multi-sleeve or under-counter dispensing solution may be worth considering.

If you are unsure whether this model fits your cup stock or your counter setup, the team is happy to help you confirm compatibility before you order.

The San Jamar C3500CF is an in-counter cup dispenser designed to hold and dispense large-format cups with a rim diameter of 101 to 124mm. It mounts into a counter cut-out and presents cups at an angle, allowing staff to retrieve a single cup cleanly with one hand without breaking stride — a small but meaningful advantage during a busy service period.

Cup dispensing is one of those functional details that rarely gets attention until something goes wrong. A dispenser that allows cups to jam, drop, or nest badly creates friction at the point of service and slows throughput. The C3500CF uses a patented adjustable collar that conforms to the cup in use and a locking mounting ring that holds the unit securely within the counter without requiring additional support. Interchangeable springs allow the dispenser to be matched to different cup types, which helps maintain consistent feed even as cup stock varies between deliveries.

• Adjustable collar conforms to cup dimensions without tools
• Locking mounting ring provides a stable, self-supporting counter fit
• Angled presentation supports smooth one-handed retrieval at pace
• Interchangeable springs matched to cup type for consistent dispensing
• Stainless steel construction resists corrosion in wet service areas

Installation requires a counter cut-out of the correct diameter. This unit is designed solely for in-counter use and is not suitable for surface or wall mounting. It is a practical choice for self-service beverage counters, café service lines, fast-casual restaurants, and staff canteens where a fixed, tidy dispensing point is preferred over a loose cup stack.

This model works best where a single cup size in the 101 to 124mm rim range is used consistently. Operations dispensing several cup formats, or very high-volume venues cycling through large quantities of cups rapidly, may find a different configuration from the wider range more appropriate.

If you are working out which cup dispenser suits your counter layout or cup specification, we are happy to help you get that right before you order.

The San Jamar C3250SS is a pull-type water cup dispenser constructed in stainless steel, designed to hold and dispense large water cups in the 70–86mm diameter range. It accommodates both flat-bottom and cone-style cups and is intended for wall or flat-surface mounting, making it a practical addition to service counters, beverage stations, and cooler-side setups.

In a busy service environment, a reliable cup dispenser does a small but important job — keeping cups accessible, hygienic, and easy to replenish without slowing down service. The pull-type mechanism allows staff and customers to retrieve a single cup cleanly, reducing contact with the remaining stack. The flip cap helps protect stored cups from airborne contamination, which matters in open-counter or self-serve settings where hygiene standards need to be maintained throughout service.

Practical advantages of this dispenser include:

• Stainless steel construction resists corrosion and wipes down easily between services
• Self-adjusting fit accommodates a range of cup profiles within the 70–86mm band
• Flip cap protects cup stack from dust and contamination during service
• Mounting bracket suits cooler units or any flat vertical surface
• Pull-type dispensing minimises unnecessary contact with the cup supply

Installation is straightforward — the unit mounts via a bracket to a flat surface or cooler side and requires no utilities. It is worth confirming your cup size falls within the compatible diameter range before ordering, as this model is sized for larger water cups and will not suit standard 70mm or smaller portion cups.

This dispenser is well suited to canteens, healthcare facilities, water cooler stations, buffet counters, and any operation where self-serve cup access needs to be hygienic and orderly. For sites with unusually high cup throughput or where a larger-format dispenser is needed, it is worth exploring whether a higher-capacity option would be more appropriate.

If you are unsure whether this model is the right fit for your setup, our team is happy to help you work through the options.

The San Jamar C2210SM is a wall-mounted cup dispenser designed for self-service and counter-service beverage stations. It dispenses cups one at a time from a protected stack, keeping them hygienic and accessible without cluttering the worktop. The unit accepts paper, plastic and foam cups across a 73–94mm rim diameter range, which covers a broad spread of standard cup formats commonly used in hospitality and catering.

The EZ-Fit system is the practical detail that separates this model from fixed-size dispensers. Four interchangeable pre-cut gaskets are included, allowing the same unit to be reconfigured for different cup sizes within the compatible range. For operations where cup format varies by drink type, or where supply chain changes occasionally mean switching brands, this removes the cost and inconvenience of buying an additional dispenser. Fitting a new gasket is straightforward and requires no tools.

In service, the dispenser suits steady-flow environments well — staff canteens, coffee stations, waiting areas and self-service counters where cups are needed consistently but volume is moderate rather than high. The impact-resistant plastic construction holds up reliably in busy service areas without requiring maintenance.

• EZ-Fit gasket system allows cup size changes without replacing the dispenser
• Single-cup dispensing keeps the stack hygienic and reduces casual waste
• Surface-mount design clears the counter for other equipment
• Compatible with paper, plastic and foam cups across a practical size range
• No power or water connection required — simple to fit and reposition

Installation requires only a suitable vertical surface. There are no electrical or water connections involved. Before ordering, it is worth confirming that your cup stock falls within the 73–94mm rim diameter range, as cups outside this tolerance will not dispense reliably.

This dispenser is well suited to low- to mid-volume sites. Operations with significantly higher throughput, or those needing a larger cup capacity in a single unit, may be better served by a higher-capacity model from the same range.

If you're fitting out a beverage station and want to talk through which dispenser configuration works for your cup stock and service setup, the team is glad to point you in the right direction.

The San Jamar C4150SS is a wall- or cooler-mountable pull-type dispenser designed for small flat-bottom and cone water cups in the 57–73mm diameter range. It is built in stainless steel, making it a practical choice for environments where hygiene presentation and durability matter — front-of-house water stations, staff refreshment areas, and alongside cooler units in healthcare, hospitality, and food service settings.

In day-to-day service, the pull-type dispensing mechanism allows users to retrieve a single cup cleanly without touching remaining stock. The hinged flip cap keeps unused cups covered between refills, which is particularly relevant in open-plan or customer-facing areas where airborne contamination is a consideration. Refilling is straightforward — the cap opens fully and the tube loads from the top without tools or dismantling.

The stainless steel construction holds up well in environments where the unit may be wiped down regularly with commercial cleaning agents. The self-adjusting mechanism accommodates variation across compatible cup ranges without manual recalibration, which reduces day-to-day fuss when switching between cup suppliers.

• Flip cap protects cup stock and allows for quick, hygienic refilling
• Pull-type dispensing reduces contact with unused cups
• Self-adjusting fit suits a range of small flat-bottom and cone cups
• Stainless steel finish cleans down easily and withstands regular sanitising
• Bracket mounts to water coolers or any flat vertical surface

This dispenser is well suited to lower-to-medium footfall locations. For higher-volume sites dispensing larger cup formats, or where multiple dispense points are needed, it is worth considering a higher-capacity or multi-dispenser setup.

If you are unsure whether this unit suits your cup range or mounting situation, the team is happy to talk it through with you.

The San Jamar C3260TBL is a pull-type water cup dispenser finished in Artic Blue, designed to hold and dispense large flat-bottom or cone-style water cups in the 70–86mm diameter range. It mounts to a cooler or any flat vertical surface, making it a practical addition to self-serve drink stations, canteen counters, or front-of-house hydration points.

In busy service environments, the ability to keep cups hygienic, accessible, and clearly stocked matters more than it might seem. The flip cap on this dispenser keeps the cup stack covered between uses, reducing contamination risk in open or high-footfall areas. The transparent tube body allows staff to check cup levels at a glance without removing the dispenser or disturbing the stack — a small but useful advantage during a busy service period when restocking needs to be anticipated rather than reactive.

Practical operational benefits include:

• Flip cap protects cup stack from dust, debris, and handling contamination
• Transparent tube allows quick visual stock checks without opening the unit
• Self-adjusting mechanism accommodates a range of cup profiles without manual adjustment
• Mounting bracket suits cooler-top or flat-wall installation with minimal fixings
• Pull-type dispensing delivers one cup at a time cleanly and consistently

Installation is straightforward — the included mounting bracket requires only a flat surface and basic fixings. There are no electrical or plumbing requirements. The unit is suited to lower-volume sites such as small cafés, waiting areas, or office kitchens. For higher-throughput operations dispensing cups continuously across a full service, a larger-capacity or multi-stack dispenser may be a more practical choice.

This dispenser is well suited to sites that need a clean, tidy cup station without a complex setup — buffet counters, water cooler points, or staff canteens where presentation and hygiene matter but volume is modest. If you're unsure whether this unit fits your intended setup, the team is happy to talk it through.

The San Jamar C3260TBR is a wall- or cooler-mountable pull-type dispenser designed to hold and dispense large flat-bottom and cone water cups in the 70–86mm diameter range. It is a practical, single-function item built to keep cups hygienic, accessible, and consistently presented at a self-service or staff-service point.

In operational terms, this type of dispenser earns its place by removing the handling and contamination risks that come with stacking loose cups on a counter. Staff and customers take one cup at a time from the base, keeping the remaining stack covered and clean. The transparent tube makes it straightforward to judge when a refill is needed without removing the unit from the wall, which helps avoid service interruptions during busy periods.

Practical benefits in a commercial setting include:

• Flip cap keeps the cup stack protected from airborne contamination between refills
• Self-adjusting mechanism accommodates both flat-bottom and cone cup formats within the stated size range
• Transparent tube allows at-a-glance stock monitoring without removing the dispenser
• Mounting bracket suits flat surfaces and cooler units, giving some flexibility in positioning
• Pull-type dispensing reduces contact with the cup body, supporting basic hygiene standards

Installation is straightforward — the bracket fixes to any flat vertical surface or cooler housing, and no electrical or plumbing connection is required. The main practical consideration is confirming that the cups you intend to use fall within the 70–86mm diameter specification; cups outside this range will not dispense reliably. For higher-volume sites dispensing very large quantities of cups daily, a multi-bay or higher-capacity wall system may be worth considering.

This dispenser is well suited to cafés, canteens, healthcare waiting areas, gym facilities, and anywhere a water cooler or self-service beverage point is in regular use. It is a sensible choice where hygiene and tidy presentation matter but the requirement is modest in scale.

If you are unsure whether this model matches your cup format or station layout, the team is happy to help you confirm the right fit before you order.

The San Jamar C5450C18 Sentry is an 18-inch in-counter cup dispenser designed for fixed installation into a countertop or serving station. It accepts cups with rim diameters in the 79–114mm range, making it suitable for a broad spread of standard disposable cup sizes used in cafés, canteens, fast food operations, and self-service beverage stations. The dispenser sits flush within the counter surface, keeping the cup stack contained, hygienic, and out of reach of general customer handling.

In a busy service environment, consistent cup dispensing matters more than it might appear. The Sentry's adjustable lever mechanism is engineered to release cups one at a time cleanly, which reduces the frustration of cups jamming, double-dispensing, or arriving at the counter crushed. The adjustment can be made even with cups already loaded, which is a practical advantage during a service period when stopping to clear and reload the dispenser is not realistic.

From an operational and hygiene standpoint, the design includes a contamination guard that limits debris entering the tube from above, and the tube itself is a translucent blue material — a recognised food safety colour — which allows staff to carry out a quick visual check on cup levels and cleanliness without dismantling anything.

• Trim ring around the counter opening discourages customer tampering
• Lever adjustment accessible during live service without unloading cups
• One-at-a-time dispensing reduces cup damage and waste
• Translucent blue tube supports quick hygiene and stock-level checks
• Compatible with a wide rim diameter range, reducing the need for multiple dispensers

This model is well suited to counters with a moderate to high throughput of hot or cold drinks — coffee shops, hospital or workplace canteens, and fast casual restaurant service stations being typical environments. For very high-volume sites where multiple cup sizes are in simultaneous use, it is worth considering whether a surface-mounted or multi-unit configuration would better serve the operation.

If you are unsure whether the C5450C18 is the right fit for your counter depth, cup stock, or service layout, our team is happy to talk it through with you.

The San Jamar C3165FBL is a wall or surface-mounted pull-type cup dispenser designed for medium water cups in the 64–83mm diameter range. It accepts both flat-bottom and cone-style cups, making it a practical choice for sites that use standard single-use water cups at self-service stations, buffet lines, water coolers, or beverage counters.

In busy service environments, a reliable cup dispenser is a small detail that has a noticeable impact on flow. Cups are dispensed one at a time with a downward pull, which keeps the remaining stack clean and reduces the chance of multiple cups being grabbed at once — a common source of waste in high-footfall settings. The transparent tube allows staff to monitor cup levels at a glance, so refilling can be managed before stock runs out mid-service rather than reactively.

Practical benefits for operators include:

• Flip cap protects the cup stack from airborne contamination between refills
• Self-adjusting mechanism accommodates a range of medium cup sizes without manual adjustment
• Transparent tube gives clear visibility of remaining cup levels
• Mounting bracket suits water coolers and flat wall or cabinet surfaces
• Impact-resistant plastic construction holds up to regular daily use

Installation is straightforward — the bracket mounts to most flat surfaces without specialist tools, and no electrical or plumbing connection is required. It's worth confirming cup diameter compatibility before ordering, as cup sizes vary between suppliers and not all medium cups fall within the stated range.

This dispenser is well suited to cafés, canteens, waiting areas, healthcare facilities, and anywhere a tidy, hygienic cup point is needed. It's a single-position unit, so sites with multiple service points will need one per station. For higher-volume sites or larger cup formats, alternatives with greater capacity or different size ranges may be more appropriate.

If you're unsure whether this model suits your cup stock or service setup, our team is happy to help you check compatibility before you order.

The San Jamar C3400EF is a surface-mount foam cup dispenser designed to hold and dispense 12 to 24oz foam cups in a controlled, hygienic single-cup presentation. It is built from 26-gauge 304 stainless steel and intended for fixed installation in beverage service areas, whether that is a self-service station, a staffed counter, or an end-cap position.

In busy service environments, consistent cup dispensing matters more than it might seem. A poorly positioned or poorly sized dispenser leads to cups being grabbed in handfuls, contamination of the rim area, or cups jamming mid-service. The C3400EF addresses this with an adjustable collar that conforms to different cup diameters within the supported range, allowing the dispenser to be set correctly for the specific cup stock in use rather than relying on a one-size-fits-all fit.

The practical advantages of this unit include:

• Mounts horizontally, vertically or at a 45-degree angle to suit counter layout and access requirements
• Adjustable collar accommodates foam cup rim diameters across the 70-98mm range
• Stainless steel construction supports regular cleaning and resists corrosion in damp service areas
• Single-cup elevator dispensing reduces rim contamination and cup waste
• Suitable for under-counter, wall-mount or end-cap positions

Installation is straightforward, though it is worth noting that different spring sets are required depending on the mounting orientation chosen — horizontal, vertical and angled positions each use a different spring. This should be confirmed at the point of ordering if your installation position is already fixed. The unit is surface-mounted, so no internal cabinetry is needed, but the mounting surface must be stable enough to support the unit and a full column of cups without flex.

This dispenser is well suited to cafes, staff canteens, vending areas, hospitality back-bars and any site using foam cups in the 12-24oz range as their standard format. It is a single-sleeve unit, so sites with very high throughput or multiple cup sizes in simultaneous use may find a multi-sleeve or higher-capacity dispensing system more practical.

If you are unsure whether this unit suits your counter layout or cup specification, the team is happy to help you confirm the right fit before you order.

The San Jamar C5250C18 Euro Sentry is an in-counter cup dispenser designed to present cups one at a time at the point of dispensing, keeping the counter clear while maintaining a consistent, hygienic supply. It accommodates cups with rim diameters in the 62–92mm range and sits flush within a counter cutout, making it a practical choice for self-service beverage stations, staffed coffee counters, and front-of-house drink service areas.

In busy service environments, reliable cup dispensing is often overlooked until it causes problems — cups jamming, being handled unnecessarily, or contaminated by debris settling into an open stack. The Euro Sentry addresses these issues with an enclosed tube design and an adjustable dispensing mechanism that can be set and fine-tuned even with cups already loaded, reducing service interruptions during peak periods. The dispenser presents one cup at a time, which supports consistent hygiene practice across self-service and assisted service alike.

Practical operational advantages include:

• Adjustable dispensing levers that can be set without unloading the dispenser
• Enclosed tube with a contamination guard that limits debris entry from above
• A transparent tube section allowing quick visual stock checks without opening the unit
• A trim ring that keeps the counter installation neat and discourages tampering
• One-at-a-time dispensing that reduces unnecessary cup handling

Installation requires a counter cutout to the correct diameter for an 18-inch tube unit. The dispenser drops into the counter from above, with the trim ring sitting flush on the surface. No electrical or water connections are needed. It is worth confirming your cup range before ordering — the 62–92mm rim diameter range covers many standard soft drink and hot beverage cups, but cup compatibility should be verified against the specific cup sizes used on your site. For operations using cups outside this range, alternative models are available to suit narrower or wider rim diameters.

This dispenser is well suited to cafés, quick-service restaurants, staff canteens, and any beverage station where a clean counter and hygienic one-at-a-time cup presentation are priorities. For very high-volume sites with rapid cup turnover, it is worth considering a higher-capacity or multi-tube configuration.

If you are fitting out a beverage counter and want to confirm cup compatibility or counter cutout requirements before ordering, our team is happy to help you work through the details.

The San Jamar C3200EF is a surface-mount foam cup dispenser designed to accept 6 to 10oz foam cups with rim diameters in the 56–81mm range. It dispenses one cup at a time via an elevator mechanism, presenting the next cup cleanly at the opening and keeping the remainder protected within the tube. The unit is constructed from 26-gauge 304 stainless steel, giving it the durability expected in a busy front-of-house or self-service environment.

Where this dispenser earns its place is in speed-of-service situations — hot drink stations, self-serve beverage counters, waiting areas, and staff refreshment points — where staff or customers need to retrieve a cup cleanly and quickly without handling the stack below. The adjustable collar accommodates different cup sizes within the supported range, so operators do not need a separate dispenser for every cup specification they run.

A practical feature is the mounting flexibility. The C3200EF can be installed horizontally, vertically, or at a 45° angle, with the appropriate spring supplied for each orientation. This makes it adaptable to under-counter, wall, or end-panel positions — useful where counter space is limited or where a clean, built-in look is preferred. Key operational benefits include:

• Single-cup dispensing keeps the remaining stack hygienic and untouched
• Adjustable collar adapts to cup sizes within the supported range
• Three mounting orientations give installation flexibility in tight spaces
• Stainless steel construction is straightforward to wipe down and maintain

Installation requires only a flat surface or panel suitable for the fixing method chosen. No plumbing, electrical connection, or ventilation is needed. It is worth confirming your cup rim diameter against the 56–81mm specification before ordering, as the dispenser is designed for foam cups only and will not function correctly with paper or plastic alternatives.

This dispenser is well suited to cafés, canteens, hospital refreshment points, office kitchens, and any self-serve station running foam cups in the 6–10oz range. For sites dispensing larger cup formats or requiring a countertop-mounted or undercounter recessed solution, other configurations in the San Jamar range may be more appropriate.

If you are fitting out a beverage station and want to make sure the dispenser suits your cup specification and installation position, the team is happy to talk it through before you order.