Restaurant Equipment Accessories

The Lincat OA8912 is a purpose-built floor stand designed to support compatible Lincat salamander grills at a practical working height. Rather than relying on a fabricated shelf, a borrowed worksurface, or an improvised support, it gives the salamander a dedicated, stable base on the kitchen floor — keeping the unit accessible and the surrounding workspace clear.

In a busy service environment, ergonomics have a direct effect on throughput. A salamander at the wrong height slows down loading and retrieval, particularly during peak periods when speed and consistency are critical. This stand positions the grill where operators can work with it comfortably, rather than having to adapt their workflow around it. The construction meets applicable hygiene standards, with surfaces and joints that are straightforward to clean down — a practical consideration when environmental health compliance is part of routine kitchen management.

• Positions the salamander at a comfortable, practical working height
• Provides a stable, dedicated floor-mounted base without improvised solutions
• Designed to hygiene standards with cleanable surfaces and joints
• Keeps the grill clear of worksurface clutter and congestion
• Straightforward to install alongside a compatible Lincat salamander

This stand is designed for specific compatible Lincat salamander models, so confirming compatibility with your existing or intended grill before ordering is an important step. It requires adequate floor space and a stable, level surface, and the grill should be properly secured to the stand prior to use.

It is well suited to kitchens where a compatible Lincat salamander is already in place or being specified as part of a new installation, and where floor-mounting is the preferred or only practical option. If you are unsure whether this stand suits your grill model or available space, we are happy to talk it through.

The Cinders Double Pan Support is a purpose-built accessory designed exclusively for the Cinders Classic TG160 barbecue. It drops into position at either end of the grill and accepts two gastronorm pans, creating a practical holding and staging area directly adjacent to the cooking surface. Gastronorm pans are not included.

In a busy outdoor service environment, managing cooked food safely between the grill and the pass is an operational challenge that is often underestimated. This support addresses it directly — one pan can sit over residual heat for hot holding while the second provides staging capacity for resting or prepared items. That arrangement helps operators maintain a controlled, hygienic flow from grill to service without improvised solutions that slow throughput or introduce cross-contamination risk.

• Keeps cooked food at temperature while the grill continues in use
• Separates resting and staged food from raw product on the cooking surface
• Supports hygienic handling from preparation through to service
• Drops in and out without tools for quick setup and breakdown
• Compatible with standard gastronorm pans already in use in most operations

It is worth noting that this support is designed solely for the Cinders Classic TG160 and will not fit other Cinders models or third-party barbecues. For high-volume outdoor events where more extensive hot-holding capacity is needed, it is worth considering whether additional equipment is required before committing to a service setup.

If you would like to talk through how this accessory fits into your outdoor operation, the team is happy to help you work it out.

The Blue Seal SK2731N is a purpose-built stainless steel stand designed specifically to support the Turbofan E27M2 and E31D4 convection ovens. It raises the oven to a practical working height and provides a stable, hygienic base suited to the daily demands of a commercial kitchen environment.

Fitted with castors, the stand allows the oven to be repositioned when needed — whether for thorough deep cleaning, a kitchen layout change, or adjustments around shifting service requirements. For heavy equipment that would otherwise need to be lifted or left in place indefinitely, this is a genuine practical advantage. It is worth confirming that the castors lock securely before service, particularly if your kitchen floor has any unevenness.

Using the manufacturer-matched stand rather than a generic alternative carries straightforward operational benefits:

• Confirmed compatibility with the E27M2 and E31D4 Turbofan models
• Castors allow repositioning without lifting heavy equipment
• Stainless steel construction resists corrosion and cleans down easily
• Raises the oven to a comfortable, ergonomic operating height
• Purpose-built proportions ensure a secure, stable fit with no improvisation

Before ordering, measure your available floor space carefully. You will need to allow for any oven overhang, adequate door-swing clearance, and appropriate ventilation around the unit. This stand is not a universal fit — it should only be used with the compatible Turbofan models listed above.

This stand is the right choice for operators running or planning to install the E27M2 or E31D4 Turbofan oven. If you are building out a new setup or are unsure whether this suits your particular configuration, it is worth a conversation with the team before you order.

The Crown Verity RT48 is a rotisserie attachment designed exclusively for use with the Crown Verity MCB48 barbecue. It fits directly to the MCB48 and enables spit-roasting over live heat, adding a second cooking method to a unit that operators may already be running for standard grilling.

In outdoor catering and event hospitality settings, rotisserie cooking is a reliable way to handle whole birds and large joints at volume. The continuous rotation produces an even, self-basting effect that tends to give more consistent results across larger cuts than static grilling alone — particularly useful during long service periods where the grill is working hard and consistency matters. It is a practical extension of the MCB48's capability rather than a replacement for it, and the attachment can be fitted or removed as the menu demands.

From an operational standpoint, the main practical points to be aware of are:

• Designed exclusively for the MCB48 — compatibility is unit-specific, not universal
• Suited to whole birds, large joints, and similar proteins requiring slow, even cooking
• Supplied with 5-inch forks as standard
• Straightforward to fit and remove without specialist tools
• Extends the cooking repertoire without adding a separate piece of equipment

This attachment is best suited to outdoor event caterers, mobile hospitality operators, and venue teams already running the MCB48 who want to offer spit-roasted items alongside their standard barbecue menu. Before ordering, it is worth confirming you have the correct MCB48 model, as rotisserie compatibility is not interchangeable across different units in the Crown Verity range.

If you would like to talk through how the RT48 works alongside the MCB48 in a specific event or service context, the team is happy to help you work out whether it is the right addition to your setup.

The Lincat OA8950 is a purpose-built floor stand designed to support compatible Lincat equipment at a practical working height in a commercial kitchen. It is a model-specific accessory rather than a universal stand, so compatibility with your particular unit should be confirmed before ordering.

A well-specified floor stand contributes more to a kitchen than simply lifting equipment off the ground. Positioning a unit at the correct operating height reduces operator fatigue during busy service periods and makes routine use more comfortable over the course of a long shift. Raising equipment clear of the floor also makes cleaning underneath and around the unit considerably more straightforward — a practical consideration in any kitchen subject to environmental health inspection, where floor hygiene is routinely assessed.

In kitchens where wet cleaning is carried out regularly, having equipment elevated provides a degree of protection against moisture at floor level, which helps preserve the parent unit over its working life.

• Raises equipment to a comfortable, practical operating height
• Simplifies cleaning underneath and around the unit
• Helps protect equipment in kitchens with wet-clean regimes
• Supports compliance with commercial kitchen hygiene standards
• Purpose-built to suit compatible Lincat equipment

The OA8950 is best suited to operators configuring or replacing a Lincat equipment setup who need a correctly specified support solution. If you are building out a larger equipment package, it is worth reviewing the stand alongside the parent unit to make sure the combination works as intended within your available space.

If you are unsure whether the OA8950 is the right stand for your equipment, the team is happy to talk it through before you place an order.

The Crown Verity RT30 is a rotisserie attachment designed specifically for the MCB30 and MCB60 barbecue units within the Crown Verity range. It fits directly onto compatible units without modification or fabrication, converting an existing grill into a rotisserie cooking station and broadening the menu options available from a single piece of equipment.

Rotisserie cooking is well suited to volume service — whole birds, rolled joints, and large cuts cook consistently with minimal manual intervention, which matters during sustained outdoor service periods where staff attention is spread across multiple stations. The RT30 is relevant wherever operators need reliable, repeatable results on larger protein loads without running a separate dedicated unit.

From a practical standpoint, the key advantages for outdoor catering operations are straightforward:

• Fits directly to MCB30 and MCB60 units — no tools or fabrication required
• Suitable for whole birds and large joints in continuous service
• Supplied with forks to secure product securely during rotation
• Extends an existing barbecue's capability without additional equipment footprint
• Compact accessory format — easy to transport alongside the main unit

It is worth being clear about compatibility: the RT30 is designed exclusively for the MCB30 and MCB60 and will not fit other Crown Verity models or third-party barbecue units. If you are unsure which barbecue you are running, it is worth confirming the model before ordering to avoid a mismatch.

This is an accessory purchase that only makes sense alongside the right host unit. If you are building out a Crown Verity setup or want to talk through how the RT30 fits into your service model, we are happy to help — give us a call or send a message.

The Lincat PHTC is a ceramic panel insert manufactured specifically for the Panther Hot Cupboard range. It is a factory-fitted component, meaning it arrives installed as part of the hot cupboard build rather than as a field-fitted add-on. Its purpose is to provide a smooth, heat-retaining internal surface that supports plated dishes and gastronorm containers throughout a service period.

Inside a working hot cupboard, the quality of the holding surface has a direct effect on temperature consistency. A ceramic panel distributes heat more evenly across the base than bare metal, which helps reduce cold spots during prolonged holding — particularly relevant when the cupboard is loaded to capacity during a busy service. The surface also offers a stable, non-slip resting point, which matters when plates and containers are being placed and removed repeatedly at pace.

• Even heat distribution across the cupboard base during extended holding
• Stable, non-slip surface suitable for plates and gastronorm containers
• Smooth ceramic finish wipes down quickly between services
• Matched component for the Panther Hot Cupboard range
• Reduces surface temperature inconsistencies under sustained load

It is worth being clear that this insert is specific to the Panther range and is not a universal or retrofit accessory. If you are sourcing a replacement for a damaged panel or specifying a new Panther unit, confirming the correct component reference before ordering will avoid compatibility issues further down the line.

If you are specifying a Panther Hot Cupboard or are unsure whether this component is right for your existing unit, we are happy to talk it through before you order.

The Crown Verity PGRID48 is a full-width griddle plate designed specifically for the MCB48 barbecue unit. It slides directly into the cooking position in place of the standard grill grates, converting the MCB48 into a flat-top cooking surface without any tools or permanent modification. It is a dedicated accessory, not a universal fit, so it is worth confirming you have the MCB48 before ordering.

The plate is constructed from thick rolled steel, which gives it the mass to hold temperature consistently across the full surface when food is loaded. In a busy outdoor service environment — events catering, festival operations, large hospitality functions — this matters. A thinner plate would shed heat quickly under volume; the PGRID48 maintains cooking temperature through continuous service in a way that keeps throughput steady rather than forcing the operator to work in smaller batches.

Practical features that make a difference in service include:

• Slide-on fitment allowing quick conversion between griddle and open grill cooking
• Thick rolled steel construction for consistent heat retention under load
• Removable grease tray for faster cleaning between service periods
• Integrated splashguard to reduce mess and protect the operator
• Designed exclusively for the MCB48, ensuring a secure, stable fit

As a removable accessory, it gives operators the flexibility to switch between grill and griddle cooking depending on the menu — a useful characteristic when outdoor event menus vary from one day to the next. Cleaning is straightforward given the removable grease management, which matters when turnaround between services is tight.

If you are unsure whether the PGRID48 suits your current MCB48 setup, or want to talk through outdoor cooking accessories more broadly, the team is glad to help you work through it.

The Lincat BA116 is a quarter-size pasta basket designed to work within the Lincat PB33 and PB66 pasta cookers. It sits inside the main tank and divides the cooking area into smaller sections, allowing different pasta varieties or separate portion sizes to be managed independently without running additional equipment.

In a working kitchen, that flexibility becomes genuinely useful once service picks up. Rather than committing the full tank to a single product, a quarter basket lets you respond to individual orders, run a side pasta alongside a main dish, or hold smaller batches ready to go without over-producing. It is a straightforward way to get more organised use from equipment you already have.

• Divides the tank into quarter sections for flexible, simultaneous batch cooking
• Allows multiple pasta varieties to run in one unit at the same time
• Supports smaller portion batches, helping to reduce waste during quieter periods
• Compatible with both the Lincat PB33 and PB66 pasta cookers
• Easy to lift, drain, and clean quickly between uses during service

There are no installation requirements — this basket drops straight into your existing pasta cooker with no modification needed. The one thing worth confirming before ordering is your pasta cooker model. The BA116 is sized specifically for the PB33 and PB66 and is not a universal fit across other pasta cooker ranges.

It suits any kitchen already running one of the compatible Lincat models that wants more control over pasta service output. If you are building out a pasta station from scratch and are not yet sure which configuration fits your service volumes, we are happy to talk it through before you order.

The Crown Verity ABR30 is a purpose-built bun rack designed specifically for use with the MCB30 and MCB60 gas barbecue units. It sits inside the RD30 roll dome, making use of the residual heat generated above the main cooking surface to warm buns, rolls, or bread without exposing them to direct flame or grill contact.

In a busy outdoor service environment — whether that is event catering, outdoor hospitality, or mobile food operations — keeping buns warm and ready throughout service is a small but operationally meaningful detail. A cold or stale bun slows service and affects the finished product. The ABR30 allows operators to run bun warming and main cooking simultaneously from the same unit, without needing a separate holding appliance taking up additional space or power.

Four adjustable height positions give a degree of control over heat exposure, which is practical when service pace varies or when the grill is running at different intensities across a shift.

• Fits inside the RD30 roll dome — no additional counter or table space required
• Four height positions allow heat exposure to be managed during service
• Warms buns without direct flame or grill contact
• Eliminates the need for a separate holding unit at the service point

This is a model-specific accessory and will not fit barbecue units or roll domes outside the MCB30 and MCB60 range. It is worth confirming your existing Crown Verity configuration before ordering.

If you are building out a Crown Verity setup from scratch or want to check compatibility with your current equipment, the team is happy to talk through the right combination of units and accessories.

The Blue Seal SK32 is a purpose-made stainless steel stand designed exclusively to support the Blue Seal E32D4 Turbofan convection oven. Rather than resting the oven on a fabricated bench or an unrated generic support, this stand provides a correctly matched base that holds the unit at a practical working height while keeping the floor area beneath clear and accessible.

The castors are a straightforward but genuinely useful feature in a working kitchen. Being able to roll the oven away from the wall — for cleaning behind the unit, for a service visit, or during a kitchen reconfiguration — removes the need to lift or drag a heavy appliance across the floor. That has a direct bearing on staff safety, floor condition, and the long-term integrity of utility connections.

• Stainless steel construction suited to the demands of a commercial kitchen environment
• Castors allow safe repositioning without lifting or dragging the oven
• Designed to match the E32D4 footprint and carry its load correctly
• Positions the oven at a practical service height for kitchen staff
• Clears the floor beneath, making routine cleaning straightforward

It is worth being clear that the SK32 is designed for the E32D4 specifically. It is not a universal stand and should not be assumed compatible with other models without checking first. This is also an item that is easy to overlook when putting together a new oven specification — it is worth confirming whether a stand is included in your supply before the equipment arrives on site.

If you are specifying an E32D4 installation and want to talk through what else you may need, the team is happy to help.

The Lincat OA8925 is a genuine manufacturer accessory designed to divide the cooking tank of a compatible Lincat pasta cooker into smaller independent sections. Rather than managing an entire tank as a single batch, operators can cook individual portions or separate pasta varieties simultaneously, lifting and draining each basket independently as orders come in.

During a busy service, that independence matters. A basket of penne can be lifted and drained while tagliatelle continues cooking alongside it, which helps maintain ticket times and prevents the over-cooking that tends to occur when a full tank is held waiting for a single large batch to finish. For kitchens with varied pasta menus or strict portion discipline, this kind of control is a practical everyday advantage rather than a marginal one.

Using a genuine Lincat accessory ensures correct fit within the unit — proper immersion depth, secure handling, and consistent drainage. These details can seem minor until service pressure reveals them. Third-party baskets sometimes introduce small inconsistencies in fit or depth that only become apparent when speed is critical.

• Divides the cooking tank for simultaneous, independent portion cooking
• Allows individual baskets to be lifted without disturbing others
• Genuine Lincat accessory with correct fit for compatible units
• Reduces waste from batch over-cooking during service
• Supports consistent portioning across varied pasta menus

Compatibility varies across the Lincat pasta cooker range, so if you are unsure whether this basket suits your existing unit or are building out a setup, we are happy to check before you order.

This is the manufacturer-supplied wall bracket designed specifically for the Convotherm 6.06 Mini combi oven. It allows the oven to be mounted at a fixed height on a suitable wall or upstand, freeing up worktop or pass space rather than occupying bench area that a busy section is rarely able to spare.

In compact or high-throughput kitchens, reclaiming worktop area can make a practical difference to how a section is laid out and how efficiently it operates during service. Positioning the oven at an appropriate working height also reduces the physical demands of loading and unloading trays continuously, which is worth considering where the unit is in regular daily use.

Because this bracket is designed and supplied by Convotherm for this specific model, it provides the correct fitment geometry for a secure, stable installation. A fabricated or generic alternative is not advisable given the combined weight and operating temperatures involved with a combi oven of this type.

• Correct manufacturer fitment for the Convotherm 6.06 Mini
• Frees up valuable worktop or pass space
• Positions the oven at an ergonomically practical working height
• Provides a stable, secure mount for a heavily used piece of equipment
• Removes the need for a separate stand or purpose-built support structure

Installation requires a structurally sound wall capable of bearing the loaded weight of the oven. The suitability of the wall surface and fixing substrate should be assessed before fitting — this is particularly relevant in older builds, partitioned kitchen layouts, or where stud walls are involved. Confirmation of fixing requirements with a qualified engineer is advisable before proceeding.

This bracket is a model-specific accessory and is not compatible with other Convotherm units or third-party combi ovens. It is well suited to operators running the Convotherm 6.06 Mini in compact kitchens where layout efficiency matters and bench space is limited.

If you are weighing up wall-mounting against a stand or worktop position, or want to understand what the installation involves before committing, the team is happy to talk it through.

The Crown Verity RES is a removable end shelf designed specifically for use with the MCB range of Crown Verity commercial barbecues. It fixes directly to the end of the grill unit, giving operators a dedicated surface immediately adjacent to the cooking area — useful for resting cooked food, plating, or keeping utensils and condiments to hand without needing a separate table or side unit.

In outdoor catering and events environments, having usable workspace right at the grill makes a real difference during service. Operators can keep the main cooking surface clear, move food efficiently from grill to service without stepping away, and maintain a tidier, more controlled setup throughout a busy period. When the shelf is not required — during transport, at the end of an event, or in storage — it removes cleanly, which is a practical advantage for mobile caterers and venues where the barbecue is regularly relocated.

• Attaches directly to the MCB barbecue, adding staging space at the grill
• Removable design makes transport and compact storage straightforward
• Keeps the main cooking surface clear during peak service
• Reduces reliance on separate tables or side furniture at outdoor events
• Compatible across the Crown Verity MCB barbecue range

It is worth noting that this shelf is designed specifically for the MCB series and is not a universal fit for other Crown Verity models. If you are planning a broader outdoor catering setup and want to make sure you are selecting the right MCB model and accessories to match your service operation, we are glad to help you work through the options.

The Lincat GR7/WS is a wall-mounting shelf made specifically for the Lincat GR7 salamander grill. Rather than sourcing a general-purpose bracket or fabricating something on site, this shelf is matched to the GR7's footprint and fixing points, providing a secure and correctly positioned mount above the cooking line without any guesswork.

Wall-mounting a salamander makes a genuine difference to day-to-day kitchen workflow. Positioning the unit at the right height lets operators work beneath it efficiently — finishing plates, browning, or glazing — whilst keeping counter space free for active service use. It also simplifies cleaning along the cooking line and helps maintain a clear, organised pass during busy periods, which matters when the kitchen is running at pace.

• Frees up counter space beneath the grill for active service use
• Positions the GR7 at a practical working height for operators
• Purpose-matched to the GR7, removing the need for improvised brackets
• Simplifies cleaning around the base of the unit and along the range top
• Contributes to a tidier, better-organised pass setup during service

This shelf is designed for the GR7 model specifically and should not be assumed compatible with other Lincat salamander variants. Wall fixings will need to be appropriate for the surface — a solid masonry wall or adequately studded partition with suitable anchors is the standard requirement. If there is any uncertainty about wall construction or load-bearing suitability, it is worth confirming this before installation begins.

The GR7/WS suits any site running a Lincat GR7 salamander where wall-mounting is the preferred arrangement over counter placement — most commonly pub kitchens, café operations, and smaller restaurant sites where worktop space is at a premium.

If you are specifying this shelf alongside a new GR7 installation or have questions about wall fixing requirements, the team are glad to talk it through before you commit.

The Lincat OA8908 is a purpose-built bench stand designed to support compatible Lincat salamander grills at a practical working height on a countertop or preparation surface. Rather than sitting the grill flush on a flat bench, the stand raises it so chefs can load, monitor, and clear food more naturally during service without stooping or interrupting their workflow at the station.

In a working kitchen, grill height has a measurable effect on how smoothly service runs. A salamander positioned too low on a busy pass creates awkward movement at a point in the operation where efficiency matters most. A consistent, stable working position makes the station easier to manage across a full service, particularly where chefs are covering multiple sections at once.

From an operational standpoint, the stand also contributes to a tidier, safer grill station:

• Raises the salamander to a more accessible working height on the bench
• Provides a stable, fixed base that reduces movement and vibration during use
• Keeps the underside of the grill clear, supporting airflow and surface hygiene
• Matched to specific Lincat salamander models, ensuring a secure and stable fit
• Supports compliance with commercial kitchen surface hygiene requirements

It is worth confirming compatibility with your specific salamander model before ordering. This stand is matched to particular Lincat units, and fitting an incompatible grill introduces both a stability and a safety risk. If you are specifying a new salamander and stand together, or are unsure whether this suits your existing equipment, it is worth checking before purchasing.

If you would like to confirm compatibility or talk through how this fits into your grill station setup, the team is happy to help.

The Lincat BA114 is a half size pasta basket made specifically for use with the Lincat PB33 and PB66 pasta cooker models. It fits directly into the cooker tank and is intended either as a like-for-like replacement for a worn or missing basket, or as an additional basket to expand how the cooker is used during service.

In a working kitchen, how you configure your pasta cooker has a practical effect on service flow. Running two half size baskets simultaneously allows different pasta types or portion sizes to be cooked in the same tank without mixing — useful when you are covering multiple dishes from a single unit. During quieter covers, a half size basket also means you are not committing to a full load, which supports tighter portion control and reduces waste at the end of service.

• Fits directly into Lincat PB33 and PB66 pasta cooker tanks
• Allows two pasta types to cook simultaneously within a single unit
• Practical for lower-volume periods or where portion control matters
• Easy to lift, drain, and return to the tank during a busy pass
• A sensible spare to hold in reserve if the original basket is in use or needs replacing

It is worth confirming your cooker model before ordering. The BA114 is only compatible with the PB33 and PB66 — it will not fit other Lincat pasta cooker ranges. If you are unsure whether a half size basket suits your current service style, or whether your pasta cooker setup is working as efficiently as it could, we are happy to talk it through.

The Lincat BA83 is a genuine half size mesh fryer basket made specifically for use with the Lincat Opus fryer range. It is a direct replacement or supplementary spare, not a universal accessory — it is sized and constructed to fit and function as intended within Opus fryer tanks.

In a busy service, basket condition is often underestimated as a factor in consistent results. A correctly fitted basket ensures even oil submersion, reliable cook times, and controlled lifting when handling product at full frying temperature. The half size format is well suited to kitchens running smaller batch quantities, or to operators splitting a single tank across two baskets — a practical approach when managing allergen separation or running products with different cook times simultaneously.

Fryer baskets do wear with regular use. Handles can degrade, mesh can distort or corrode over time, and a basket that no longer sits correctly in the tank introduces unnecessary handling risk during service. Keeping a spare in stock is straightforward good practice for any operation that runs its fryer hard through a shift.

• Genuine Lincat accessory — designed and built to fit the Opus fryer range
• Half size format supports split-batch and allergen-separation working
• Correct tank fit ensures consistent oil submersion during frying
• Moulded handle for controlled, safe lifting from hot oil
• Standard mesh construction suited to everyday commercial deep frying

This basket is intended for operators already running a Lincat Opus fryer. It is not compatible with other fryer makes or models. If you are unsure whether the BA83 is the correct fit for your specific Opus model, or if you need full size basket options, the team is happy to help clarify before you order.

Rational Care Tabs are the manufacturer's own maintenance consumable for iCombi Pro, iCombi Classic, and SelfCookingCenter units fitted with CareControl. They are used as part of the oven's automated care cycle, working to protect the internal water circuit and steam-generating components from the gradual accumulation of limescale and mineral deposits.

Water quality has a direct bearing on how consistently a combi oven performs and how long it remains in reliable service. Limescale build-up in the steam system is one of the more common causes of performance drift and unplanned downtime in high-use units. These tabs address that progressively rather than reactively — the formulation is intended to prevent scale taking hold in the first place, which reduces the need for more disruptive descaling procedures that take the oven offline during service.

• Prevents limescale accumulation in the steam circuit during normal operation
• Reduces component wear associated with prolonged mineral deposit build-up
• Supports consistent steam output and cooking performance throughout service
• Integrates directly with the oven's CareControl automated dosing system
• Supplied in a tub suited to regular, ongoing use in a working kitchen

Being a Rational-specified product matters here. The tabs are formulated to work within CareControl as the system was designed to operate. Substituting non-approved alternatives can affect how the care cycle functions and may carry implications for warranty coverage — something worth weighing carefully when comparing against lower-cost options.

Water hardness varies considerably across different parts of the UK, and the appropriate care schedule for a site can differ from one operation to the next. If you'd like to talk through care intervals or water quality considerations for your kitchen, the team is happy to help you work it out.

The Rational Stand II is a stainless steel floor stand manufactured and approved by Rational specifically for use with the iCombi 6-2 and iCombi 10-2 combi oven models. It provides a stable, purpose-built base that brings the oven to a practical working height without relying on fabricated or improvised support structures that may not distribute the load correctly.

In a working kitchen, the distinction between a manufacturer-approved stand and a generic alternative becomes clear quickly. The closed side and top panels prevent grease and debris accumulating in hard-to-reach areas, which supports day-to-day cleaning routines and makes hygiene audits more straightforward. The open rear panel keeps water inlets, drain connections, and service access points unobstructed — an important consideration both during initial installation and for any maintenance work carried out later. The stand's rail support is designed to handle the specific weight and load distribution of the iCombi units, which avoids the stress concentration that can occur with non-approved alternatives over time.

Practical reasons to specify this stand alongside the oven:

• Positions the oven at the correct working height from the outset
• Closed panels support cleaning routines and assist with hygiene compliance
• Open rear preserves access to utility connections and service points
• Rational-approved for the iCombi 6-2 and 10-2 — no fitment uncertainty
• Stainless steel construction handles commercial kitchen cleaning regimes reliably

This stand is suited to kitchens where the iCombi 6-2 or 10-2 is being installed as a standalone floor-standing unit. It is not designed for larger iCombi cabinet formats and is not intended for stacked configurations. If you are working through how the stand fits within your available floor space or service layout, the team is happy to talk it through before you finalise the order.

The Lincat GR3/WS is a wall-mounted shelf designed specifically to match the Lincat GR3 salamander grill. Its purpose is straightforward: to provide a secure, correctly rated fixing point that positions the GR3 at a consistent working height on the wall, freeing the counter or pass surface beneath for other use.

In a working kitchen this arrangement makes a practical difference. A wall-mounted salamander sits at a fixed, repeatable height throughout service, remains stable under the incidental contact that bench-mounted units can attract, and allows operators to work comfortably beneath it without obstruction. Cleaning around and below the unit at close-down is also more manageable when the space is fully clear.

Using the manufacturer-matched shelf is worth doing for reasons beyond convenience. The GR3/WS is engineered to align with the GR3's fixing geometry and carry its load correctly. A generic bracket may not suit the unit's weight distribution or mounting points, which introduces unnecessary risk in a busy service environment.

Installation requires the shelf to be fixed securely into a wall capable of bearing the combined weight of the shelf and the grill. Wall construction varies — solid masonry, stud partitions, and tiled surfaces each call for different fixings and approaches — so it is worth assessing the substrate before ordering. Fixing should be carried out by a competent installer or kitchen fit-out contractor rather than attempted without the appropriate fixings for the wall type.

This shelf suits any kitchen running a Lincat GR3 salamander where wall placement is the preferred arrangement. If you are considering the installation approach or want to confirm the GR3 is the right unit for your kitchen, the team is happy to talk it through with you.

Rational's Active Green cleaner tabs are the manufacturer-specified cleaning consumable for iCombi Pro and iCombi Classic combi ovens fitted with Efficient Care Control. They are formulated to work directly with the oven's built-in automated cleaning programmes, delivering the correct detergent concentration for each cycle without requiring manual intervention or separate chemical measuring.

In a working commercial kitchen, oven cleanliness has a direct bearing on cooking consistency and equipment life. Grease and food residue that builds up across services can affect airflow, impair steam generation, and interfere with sensor accuracy. Using the correct manufacturer-specified tab ensures the automated cycle performs as the oven's software expects — with the chemistry matched to the programme parameters rather than approximated by a third-party alternative.

A practical consideration for sites in areas with variable water quality is that the Active Green formulation is designed to operate without the need for a separate water softener or routine manual descaling. This reduces day-to-day maintenance demands and simplifies stock management. Operational advantages include:

• Matched to Rational's automated cleaning cycle parameters on compatible models
• Works in typical commercial water conditions without a separate water softener
• Removes grease and food soiling through a multi-ingredient cleaning complex
• Eliminates manual descaling between services under normal operating conditions
• Supplied in cartons for straightforward stores-room stock control

These tabs are appropriate for any site running a compatible Rational iCombi Pro or iCombi Classic with Efficient Care Control — including hotel kitchens, contract catering, restaurants, and education catering. It is worth noting that using non-Rational cleaning products in these ovens can affect how cleaning programmes perform and may carry warranty implications.

If you are working through which Rational cleaning consumables are correct for your oven model or want to check compatibility, the team is glad to point you in the right direction.

The Crown Verity PGT1117 is a perforated grill plate designed to fit the full MCB range of Crown Verity barbecues. The perforated surface allows heat and smoke to circulate around food while preventing smaller items from falling through the grill grates — a practical solution for caterers cooking fish, vegetables, or other delicate produce on a commercial outdoor setup.

In a busy outdoor catering or events environment, this kind of accessory earns its place quickly. Fish fillets, asparagus, sliced courgette, and similar ingredients that would be lost or damaged on open grates cook evenly and stay intact, reducing waste and improving plate presentation. The plate sits directly on the existing MCB grill surface, so there is no complex setup involved.

Key practical advantages include:

• Prevents delicate fish and vegetables from falling through grates
• Allows smoke penetration and char flavour to develop naturally
• Compatible across the MCB barbecue range — no additional adapters needed
• Simple to remove and clean between service periods
• Expands menu flexibility on an existing MCB unit

This is a straightforward accessory rather than a complex piece of equipment, but it is worth confirming compatibility with your specific MCB model before ordering. If you are putting together a full outdoor catering station or are unsure which Crown Verity accessories suit your setup, the team is happy to help you piece it together sensibly.

This is the manufacturer-supplied open stand designed specifically for the Rational iCombi in 6-2 and 10-2 configurations. Rather than sourcing a generic platform or adapting an alternative solution, this stand is built to the correct dimensions and load ratings for these two oven models, positioning the unit at a practical working height and keeping it properly supported throughout service.

In a busy kitchen, oven height has a direct effect on how efficiently staff load and unload trays during service. A correctly positioned oven reduces unnecessary bending and helps maintain a steady workflow when covers are high. The open-frame construction allows airflow beneath the unit and gives cleaning staff unobstructed access to the floor — a straightforward consideration in kitchens where hygiene compliance is closely managed.

• Matched to the 6-2 and 10-2 iCombi footprint — no adaptation or modification required
• Open frame design allows cleaning access beneath the oven without obstruction
• Positions the oven at a practical working height for loading and unloading
• Rated to carry the weight and operational loads of these specific models
• Sourced directly from Rational, ensuring dimensional and finish consistency

Before installation, it is worth confirming the kitchen floor is level, as with any freestanding oven support. Where space is limited, or where a second iCombi is being stacked, a different stand configuration will be required — this open stand is intended for floor-standing single-unit installations only.

This stand suits operators installing a 6-2 or 10-2 iCombi as a standalone floor-standing unit who want a properly matched, manufacturer-approved support. Kitchens running other iCombi sizes will need the corresponding stand variant for those models.

If you are planning a new Rational installation and want to confirm the right stand before ordering, the team is happy to help you think it through.

These are the genuine Rational-formulated cleaning tablets designed specifically for use with the SelfCookingCenter and CombiMaster Plus ranges. They are the red tabs used in Rational's automated cleaning programmes and are sold in a tub of 100.

Rational engineers the chemistry of these tabs alongside the oven's cleaning cycles, which means the concentration and release profile of the active ingredients is calibrated to work with the built-in programme rather than against it. Using third-party alternatives can affect cleaning results and, in some cases, may affect warranty compliance — so operators running Rational equipment are generally better served staying with the manufacturer's own chemistry.

In a busy kitchen, reliable oven hygiene is not just about compliance — it directly affects food quality and oven longevity. Grease and residue left in a combi oven accelerates wear on seals and internal components. Consistent use of the correct cleaning tabs as part of each cleaning cycle helps maintain the oven in the condition it was designed to operate in.

These tabs suit any kitchen running Rational SelfCookingCenter or CombiMaster Plus equipment, from single-unit hotel kitchens through to multi-oven production sites. If you are unsure which cleaning programme or tab type applies to your specific oven model or generation, the team is happy to advise before you order.

The Crown Verity RD30 is a roll dome lid designed specifically to fit the MCB30 and MCB60 barbecue units. It sits over the cooking surface and encloses the heat, converting an open-flame grill into a covered cooking environment — closer in behaviour to an indirect grill or a low-level oven. It requires no modification to the base unit and fits without adaptation, provided you are running one of the two compatible models.

In a live outdoor catering environment, the practical difference is noticeable. Enclosing the cooking surface holds heat more effectively, which evens out temperature across the grill and reduces the recovery time between batches. For operators running continuous service at events, festivals, or large outdoor functions, that consistency makes a real difference to throughput and food quality, particularly when working through a varied menu that includes thicker cuts or items that benefit from indirect heat.

Adding the RD30 to an existing setup brings a number of operational advantages:

• Improved heat retention, which supports more consistent results across the cooking surface
• Faster temperature recovery between service batches
• Ability to roast, smoke, or cook indirectly — not possible on an open grill
• Reduced fuel consumption during extended service periods
• Broader menu flexibility without adding another piece of equipment

It is worth confirming your base unit model before ordering. The RD30 is matched to the MCB30 and MCB60 footprint and is not a universal fit across the wider Crown Verity range.

This lid suits operators who are already running Crown Verity MCB barbecues and want to extend their cooking capability without a significant further investment. If your operation demands a higher-output solution from the outset, it is worth discussing the broader Crown Verity range to find the right combination of units and accessories.

If you would like to talk through whether the RD30 works for your current setup, the team is glad to help you think it through.

The Lincat OA8951 is a dedicated floor stand designed specifically to support the Lincat OG8402 chargrill at a practical working height. Rather than resting the chargrill on a fabricated surface or general-purpose table, this stand provides a matched, stable base that integrates cleanly with the unit it is built for.

In a busy kitchen, working height makes a real difference over a long service. Raising the chargrill to an ergonomic level reduces operator fatigue and allows for consistent control during continuous use. Elevating the unit off the floor also keeps it clear of floor-level contamination and makes it considerably easier to clean beneath and around the equipment — a straightforward but meaningful contribution to maintaining hygiene standards.

• Purpose-matched to the Lincat OG8402 for a stable, clean installation
• Raises the chargrill to an ergonomic working height for continuous service
• Keeps the unit clear of floor-level contamination
• Simplifies cleaning access beneath and around the chargrill
• Supports compliance with commercial kitchen hygiene requirements

Installation is straightforward. It is worth checking that the floor is reasonably level before positioning the stand, particularly in older premises where slight unevenness could affect stability. The chargrill itself is sold separately and is not included with this stand.

This stand is suited to operators running the Lincat OG8402 who want a proper, compliant installation rather than an improvised arrangement. It is a simple addition, but one that contributes meaningfully to daily workflow and longer-term hygiene compliance.

If you are configuring a cooking suite or want to confirm this is the right fit for your setup, we are happy to talk it through before you order.

The Crown Verity PGRID30 is a 750mm removable griddle plate designed exclusively for use with the Crown Verity MCB30 and MCB60 barbecue units. It fits directly onto the barbecue via a slide-on mounting system and converts the open grill into a flat-top cooking surface without tools or any meaningful downtime between the switch.

In outdoor catering and event environments, having flat-top capability alongside a grill matters more than it might seem at first. A wide range of menu items — eggs, bacon, onions, smash burgers, pancakes — simply cannot be prepared on an open grill without loss of product or poor results. The PGRID30 handles these reliably, and the thick rolled steel construction holds heat across the surface well during continuous service, which helps maintain consistent output when throughput is high and recovery time is limited.

• Slide-on fitment allows fast changeover between griddle and grill cooking
• Removable grease tray simplifies cleaning between service periods
• Integrated splashguard helps contain grease and reduces hazard during service
• Heavy rolled steel construction retains heat evenly under sustained use

The PGRID30 is designed to fit the MCB30 and MCB60 only — it will not fit other Crown Verity models or third-party barbecues, so it is worth confirming your unit before ordering. Like any rolled steel griddle surface, it will benefit from proper seasoning and consistent aftercare to maintain cooking performance and surface condition over time.

This accessory is well suited to outdoor caterers, festival and event operators, and hospitality venues running MCB-series Crown Verity barbecues who need occasional or regular flat-top cooking capability without investing in a separate dedicated unit. For operations where flat-top cooking is the primary output at high volume, a standalone griddle may be a more practical solution.

If you would like to talk through whether this fits your current setup or how it works alongside your existing MCB unit, the team is glad to help you work it out before you order.

The Crown Verity RT72 is a purpose-built rotisserie attachment designed exclusively for use with the Crown Verity MCB72 barbecue. It converts the MCB72 into a rotisserie cooking unit capable of handling whole birds, large joints, and other substantial cuts that benefit from slow, even rotation over radiant heat. It is not a universal fitment and will not suit other BBQ models.

In a commercial outdoor cooking context — hotel terraces, event catering rigs, pub garden stations — rotisserie cooking offers a practical advantage during extended service periods. Continuous rotation promotes even cooking and natural self-basting, which reduces the need for constant staff attention and helps maintain consistency across multiple birds or joints running simultaneously. The attachment is supplied with two sets of five-inch forks, allowing more than one item to be secured on the spit at once, which helps operators manage throughput during busier services.

Practical points worth considering before purchasing:

• Designed exclusively for the MCB72 — not compatible with other Crown Verity models
• Supplied with two sets of five-inch forks for securing multiple items on the spit
• Adds rotisserie capability to an existing MCB72 without requiring a separate dedicated unit
• Well suited to outdoor events, seasonal menus, and live-cook theatre presentations

This attachment is best suited to operators who already own or are purchasing the MCB72 and want to extend its cooking range without investing in additional standalone equipment. It suits caterers running outdoor events or fixed outdoor kitchen stations where rotisserie presentation adds visible value. For sites requiring a high-throughput, dedicated rotisserie solution running independently, a standalone unit would be a more appropriate consideration.

If you're building out an outdoor cooking setup around the MCB72 and want to make sure the full configuration is right for your operation, feel free to give the team a call.